Sanyo KMHS1872 Manual Do Utilizador
Model Combinations
Combine indoor and outdoor units only as listed
below.
below.
Indoor Unit
Outdoor Unit
KMHS0772
CMH1972
KMHS0972
CMH2472
KMHS1272
CMH3172
KMHS1872
KMHS2472
Power Source:
60 Hz, single-phase, 230 / 208 VAC
60 Hz, single-phase, 230 / 208 VAC
Combinations of indoor and outdoor units
Connect indoor and outdoor units only in the combi-
nations listed in the catalog or installation manual.
Connect indoor and outdoor units only in the combi-
nations listed in the catalog or installation manual.
Connecting any other model may result in
operation failure and system damage.
operation failure and system damage.
85264189998000 © SANYO 2006
In Canada
SANYO FISHER COMPANY
SANYO Canada Inc.
A DIVISION OF SANYO NORTH AMERICA CORPORATION
300 Applewood Crescent, Concord
21605 Plummer Street
Ontario, L4K 5C7, Canada
Chatsworth, CA 91311 U.S.A.
Contents
Page
IMPORTANT!
Please Read Before Starting .................................. 2
Please Read Before Starting .................................. 2
1.
GENERAL .......................................................... 3
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Additional Materials Required for Installation
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Additional Materials Required for Installation
2.
INSTALLATION SITE SELECTION ................... 4
2-1. Indoor Unit
2-2. Embedding the Tubing and Wiring
2-1. Indoor Unit
2-2. Embedding the Tubing and Wiring
3.
HOW TO INSTALL THE INDOOR UNIT .............. 6
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Wiring Instructions for Inter-unit Connections
3-8. Mounting
3-9. Drain Hose
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Wiring Instructions for Inter-unit Connections
3-8. Mounting
3-9. Drain Hose
4.
HOW TO TEST RUN THE AIR CONDITIONER .... 16
5.
REMOTE CONTROL UNIT INSTALLATION
POSITION ......................................................... 17
5-1. Mounting on a Wall
POSITION ......................................................... 17
5-1. Mounting on a Wall
6.
ADDRESS SWITCH .......................................... 18
6-1. Address Setting of the Remote
6-1. Address Setting of the Remote
Control Unit
7.
CONNECTING A HOME AUTOMATION
DEVICE.............................................................. 19
DEVICE.............................................................. 19
8.
INSTALLATION CHECK SHEET ...................... 19
INSTALLATION INSTRUCTIONS
– Inverter Split System Air Conditioner –
COOL / DRY/ HEAT Model
This air conditioner uses the new refrigerant R410A.
Be sure to read the yellow instruction sheet
attached to the outdoor unit for models using the
new refrigerant R410A.
The illustrations are based on the typical appearance of
a standard model. Consequently, the shape may differ
from that of the air conditioner that you are installing.
NOTE
CAUTION
For Indoor Unit
05-351 KMHS0772_indoor 3/16/06 6:46 PM Page a