Friedrich XQ08 Manual Do Utilizador

 4

  

To start unit

If your air conditioner is installed and plugged into a proper re cep ta cle, it is 
ready to go. The first time the unit is started, the compressor will delay for three 
minutes. See Automatic Component Protection on the following page.

1

  Touch the Power button once. The unit will automatically be in Cool 

mode with the temperature set at 75°F (24°C) and the fan speed at 
F1, the sleep setting.

To set mode of operation

When you fi rst turn the unit on, it will be in the Cool mode (light on), with 
constant fan.

2

  Touch the Mode button once to activate the MoneySaver

 (light on).

 

 is a feature that cycles the fan with the com pres sor 

so that the fan does not run all the time.  This saves energy and 
improves  de hu mid i fi  ca tion. Or you may prefer con stant fan for more 
air move ment (to return to constant fan, touch the Mode button two 
more times).

 

In order to run the fan by itself, do the following:

3

  Continuing from MoneySaver

 mode (light on), touch the Mode button 

once to activate the FAN ONLY feature (light on).

 The 

FAN ONLY setting will circulate air in the room without the com-

pressor coming on.

To adjust temperature

4

  Use the Mode button to select either the COOL or MoneySaver

 

function

5

  COOLER – Touch the    button to lower the room air temperature.

6

  WARMER – Touch the    button to raise the room air temperature.

7

  Press both the 

  

and     buttons at the same time to switch the 

temperature readout from Fahrenheit (°F) to Celsius (°C).

 

Repeat step 7 to switch from °C back to °F.

To adjust fan speed

8

  Touch the Fan Speed button to see the current setting.  Touch it again 

to change speed.  F1 is the lowest setting (SLEEP SETTING / LOW), 
F2 is MEDIUM, and F3 is HIGH. 

To activate Smart Fan

9

  There is a fourth option, SF, when selecting the fan speed.  This is 

the SMART FAN function. SMART FAN DOES NOT OPERATE IN 
CONJUCTION WITH THE FAN ONLY MODE.

 

Smart Fan will adjust the fan speed automatically to maintain the 

desired comfort level.  For example, if the outside doors in your home 
are opened for an extended period of time, or more people enter a 
room, Smart Fan may adjust to a higher fan speed to compensate 
for the increased heat load. This keeps you from having to adjust the 
fan speed on your own.

How to operate your Friedrich room air con di tion er 

(XQ models)

10 11 12

13

7

3

4

5

6

1

8

9

2

To set the hour clock

 

10

  Touch the Set Hour button to see the current setting (clock light 

comes on).  The number that is displayed is the approximate time 
(hour only).  Use the 

  and 

 

 

 buttons to change the settings.  BE 

SURE TO SET A.M. AND P.M. ACCORDINGLY.  (P.M. is indicated 

by a red light in the upper left corner of the display).

To set the timer

NOTE:  Set the HOUR CLOCK before attempting to set timer functions.

You can set the START and STOP times a minimum of one hour apart, and 

a maximum of twenty-three hours apart.

11

  After setting the time, press the Set Hour button once (Start light 

comes on).  Use the 

  and 

 

 

 buttons to select the time that the 

unit will START.

12

  After selecting the START time, press the Set Hour button once more 

(Stop light comes on).  Use the 

  and 

 

 

 buttons to select the time 

that the unit will STOP.  After selecting the stopping time, press the 

Set Hour button once.

13

  Press the Timer On/Off button (light turns on) to activate the timer 

function.  To deactivate this function, press the Timer On/Off button 

once again (light turns off).  Once the on and off times have been 
selected, they will remain in memory and cycle daily until changed.

 

NOTE:  If the unit is unplugged or the power is interrupted, the HOUR 

must be reset or the Timer On/Off will not function when desired.

Automatic component protection

Your unit is equipped with Automatic Component Protection.  To protect the 

compressor of the unit, there is a three minute start delay if you turn the unit 
off or if power is interrupted. The fan operation will not be affected. Also, if you 
switch from Cool mode to Fan Only, and switch back to Cool mode, there 
is a three minute delay before the compressor comes back on.