Honeywell MS-9200UDLSE Manual Do Utilizador
Master Programming Level
Programming
MS-9200UDLS PN 52750:A 11/04/05
79
3.6.3.8 Zones Available
Pressing 2 while viewing Zone Setup Screen #3 will display a screen similar to the
following:
following:
The display will show all of the zones that are still available for programming. Note
that an up and/or down arrow may appear in the upper right corner of the display,
indicating that additional screens of zone information exists. Press the up or down
arrow key to view additional screens.
that an up and/or down arrow may appear in the upper right corner of the display,
indicating that additional screens of zone information exists. Press the up or down
arrow key to view additional screens.
3.6.4 Loop Setup
Loop Setup allows the programmer to configure the SLC Loop for NFPA Style 4, 6 or 7
wiring and to select the loop protocol. Pressing 1 while viewing Programming Screen
#2 will cause the following screen to be displayed:
wiring and to select the loop protocol. Pressing 1 while viewing Programming Screen
#2 will cause the following screen to be displayed:
3.6.4.1 Style
To program the SLC Style for the selected loop, press 1 for Style, while viewing
Loop Setup Screen. In the preceding example, the control panel is programmed for
Style 4 SLC wiring as indicated by the 4 to the right of Style in the display. To
change the wiring style, press 1 to toggle the display to read Style 6. Each press of
the 1 key will cause the display to toggle between Style 4 and Style 6. Note that,
when programming the Loop Style, the programmer can only select between Style 4
and Style 6. To program a system for Style 7 wiring, the programmer must select the
Loop Setup for Style 6. Style 7 wiring is the same as Style 6 with the added
requirement that each addressable device on the loop must have a pair of isolator
modules, one on each side.
Loop Setup Screen. In the preceding example, the control panel is programmed for
Style 4 SLC wiring as indicated by the 4 to the right of Style in the display. To
change the wiring style, press 1 to toggle the display to read Style 6. Each press of
the 1 key will cause the display to toggle between Style 4 and Style 6. Note that,
when programming the Loop Style, the programmer can only select between Style 4
and Style 6. To program a system for Style 7 wiring, the programmer must select the
Loop Setup for Style 6. Style 7 wiring is the same as Style 6 with the added
requirement that each addressable device on the loop must have a pair of isolator
modules, one on each side.
Note on SLC Troubles: If the FACP reports an open fault on an SLC Loop
programmed for Style 6, the trouble condition will latch at the FACP. When the
SLC Loop has been repaired, the Reset button must be pressed at the FACP (at least
2 minutes after the trouble has been repaired) to clear the SLC trouble.
programmed for Style 6, the trouble condition will latch at the FACP. When the
SLC Loop has been repaired, the Reset button must be pressed at the FACP (at least
2 minutes after the trouble has been repaired) to clear the SLC trouble.
3.6.4.2 Loop Protocol
Loop Protocol refers to the SLC loop mode of operation. The two Loop Protocols
available are CLIP (Classic Loop Interface Protocol) which is used for the older
legacy addressable devices such as the M300 Series modules and detectors and
LiteSpeed (factory default setting) which is used for the 350 Series or newer
addressable devices for quicker response times. Note that the legacy devices can
operate only in CLIP mode while the newer devices are compatible with CLIP and
LiteSpeed modes of operation. Pressing 2 while viewing the Loop Setup Screen
will toggle between CLIP and LiteSpeed Protocols.
available are CLIP (Classic Loop Interface Protocol) which is used for the older
legacy addressable devices such as the M300 Series modules and detectors and
LiteSpeed (factory default setting) which is used for the 350 Series or newer
addressable devices for quicker response times. Note that the legacy devices can
operate only in CLIP mode while the newer devices are compatible with CLIP and
LiteSpeed modes of operation. Pressing 2 while viewing the Loop Setup Screen
will toggle between CLIP and LiteSpeed Protocols.
Device Addressing
It is important to note that the MS-9200UDLS addressable device capacity is 99
It is important to note that the MS-9200UDLS addressable device capacity is 99
ZONE SETUP
1=ZONE TYPES
2=ZONES AVAILABLE
3=ZONE MESSAGE
1=ZONE TYPES
2=ZONES AVAILABLE
3=ZONE MESSAGE
Zone Setup Screen #3
ZONES AVAILABLE
01 02 03 04 05 06 07
08 09 10 11 12 13 14
15 16 17 18 19 20 21
01 02 03 04 05 06 07
08 09 10 11 12 13 14
15 16 17 18 19 20 21
PROGRAMMING
1=LOOP SETUP
2=SYSTEM SETUP
3=VERIFY LOOP
1=LOOP SETUP
2=SYSTEM SETUP
3=VERIFY LOOP
Programming Screen #2
LOOP SETUP
1=STYLE 4
2=PROTOCOL LITESPEED
1=STYLE 4
2=PROTOCOL LITESPEED
Loop Setup Screen