Cooper Lighting LA995 Folheto
INSTALLATION INSTRUCTIONS LA995 STEM KIT
HALO
®
Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX 770.486.4801 11528658
Risk of Fire / Electric Shock
If not qualified, consult an electrician
If not qualified, consult an electrician
WARNING
Keep away from flammable materials
Disconnect power at fuse or circuit breaker before
installing or servicing
installing or servicing
Risk of Electric Shock
Use only fixtures and fittings intended for use with
this kit
Use only fixtures and fittings intended for use with
this kit
Risk of Burn
Disconnect power and allow fixture to cool before
changing bulb or handling fixtures
Disconnect power and allow fixture to cool before
changing bulb or handling fixtures
SAFETY INFORMATION
Read carefully for your protection and save all instructions
• Wear rubber soled shoes and work on a sturdy wooden or fiberglass
ladder
• NOTE: Fixture should be used on a circuit that is properly protected
with a fuse or circuit breaker.
• This lighting system must be installed according to National Electric
Code and local building codes.
• To avoid a hazard to children, account for all parts and destroy all
packing materials.
• Do not install any lampholder closer than 6" from any curtain or
similar combustible material.
• Do not touch hot lens, guard or enclosure.
• Do not install in damp or wet locations
• Do not install in damp or wet locations
SAVE THESE INSTRUCTIONS
INSTALLATION OF STEM KIT TO CEILING (FIG. 1)
Step 1. Thread NUT onto STEM.
Step 2. Insert STEM through center hole in MOUNTING STRAP.
Step 3. Thread other NUT on STEM so that MOUNTING STRAP is
between the two nuts. Tighten nuts.
Step 4. Install MOUNTING STRAP onto junction box with screws
provided with the junction box.
Step 5. Slide CANOPY cover up to ceiling and fasten to STEM with
screw provided.
INSTALLATION OF STEM KIT TO TRACK (FIG. 2)
Step 1. Slide COVER onto STEM.
Step 2. Thread both nuts onto STEM allowing room for HANGER
BRACKET (installed in next step).
Step 3. Slide HANGER BRACKET between the two nuts on STEM and
then tighten.
Step 4. Raise TRACK into place and align hole in TRACK with hole in
HANGER BRACKET.
Step 5. Insert SCREW through TRACK and tighten with NUT.
Step 6. Slide COVER into place
INSTALLATION OF STEM KIT TO FEED CONNECTOR (FIG. 3)
Step 1. Remove knock-out from FEED CONNECTOR.
Step 2. Thread NUT onto STEM.
Step 3. Install FEED CONNECTOr onto STEM.
Step 4. Thread remaining NUT onto nut onto STEM and tighten.
CAUTION
Mounting holes are predrilled to accept stem kits.
For 4 and 8 foot track lengths 2 kits are required. Kits may be mounted
at connectors or at predrilled mounting hole 8 inches from end of track.
If track is field cut, and stem is not being mounted at the connector a
new hole must be drilled no greater than 8 inches from the end of the
track to mount the stem kit.
For 4 and 8 foot track lengths 2 kits are required. Kits may be mounted
at connectors or at predrilled mounting hole 8 inches from end of track.
If track is field cut, and stem is not being mounted at the connector a
new hole must be drilled no greater than 8 inches from the end of the
track to mount the stem kit.
NUT
CANOPY
COVER
NUT
NUT
STEM
FEED
CONNECTOR
CONNECTOR
HANGER
BRACKET
BRACKET
NUT
NUT
SCREW
NUT
STEM
STEM
FIG 1
FIG 2
FIG 3
NUT
MOUNTING
STRAP
STRAP