ONKYO 29344937 Manual Do Utilizador
70
2-4. Level Cal (Speaker Levels Calibration)
These settings are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 46).
You can set the volume level of each speaker so that all speakers can be heard equally at the listening position. A pink
noise test tone is output by the front left speaker.
These settings are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 46).
You can set the volume level of each speaker so that all speakers can be heard equally at the listening position. A pink
noise test tone is output by the front left speaker.
Notes:
• Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” (page 68) do not output
• Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” (page 68) do not output
the test tone.
• The speaker levels cannot be adjusted while a pair of headphones is connected or the AV receiver is muted.
Left, FrontH L, Center, FrontH R, Right, Surr R, SurrBk R,
SurrBk L, Surr L, Subwfr
SurrBk L, Surr L, Subwfr
The levels can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).
2-5. Equalizer (Equalizer Settings)
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 46).
Here you can adjust the tone of individual speakers. To set the volume of individual speakers, see page 68.
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 46).
Here you can adjust the tone of individual speakers. To set the volume of individual speakers, see page 68.
Notes:
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”,
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”,
“63Hz”, “100Hz”, or “160Hz”.
• While the Direct or Pure Audio listening mode is selected, the equalizer settings have no effect.
• The equalizer setting cannot be changed while a pair of headphones is connected.
• The equalizer setting cannot be changed while a pair of headphones is connected.
EQ
Manual: You can adjust the equalizer for each speaker manually. If you select “Manual”,
continue with this procedure.
Select a frequency
1
Use the Down [
w] button to select “Ch”, and then use the Left and
Right [
e]/[r] buttons to select a speaker.
2
Use the Up and Down [
q]/[w] buttons to select a frequency. Use
the Left and Right [
e]/[r] buttons to adjust the level at that
frequency.
The volume at each frequency can be adjusted from –6 to +6 dB in 1 dB steps.
Tip:
Low frequencies (e.g., 63 Hz) affect bass sounds; high frequencies (e.g.,
16000 Hz) affect treble sounds.
Low frequencies (e.g., 63 Hz) affect bass sounds; high frequencies (e.g.,
16000 Hz) affect treble sounds.
3
Use the Up [
q] button to select “Ch”, and then use the Left and
Right [
e]/[r] buttons to select another speaker.
Repeat steps 1 and 2 for each speaker.
Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker
Configuration)” (page 68) cannot be selected.
Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker
Configuration)” (page 68) cannot be selected.
Audyssey: The tone for each speaker is set automatically by the Audyssey 2EQ Room
Correction and Speaker Setup function. Be sure to select this setting after having
performed the Audyssey 2EQ Room Correction and Speaker Setup. “Dynamic EQ”
and “Dyn Vol” become available (page 72).
performed the Audyssey 2EQ Room Correction and Speaker Setup. “Dynamic EQ”
and “Dyn Vol” become available (page 72).
Off: Tone off, response flat.