ONKYO SKC-750XC Manual Do Utilizador
68
Recording
This section explains how to record the input source and
how to record audio and video from separate sources.
how to record audio and video from separate sources.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to the multichannel DVD input
cannot be recorded.
• Sources connected to a digital input cannot be
recorded. Only analog inputs can be recorded.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
Audio sources can be recorded to a recorder (e.g., cas-
sette deck, CDR, MD) connected to the TAPE OUT jack.
Video sources can be recorded to a video recorder (e.g.,
VCR, DVR) connected to the VCR/DVR OUT jacks.
See pages 26 to 40 for hookup information.
sette deck, CDR, MD) connected to the TAPE OUT jack.
Video sources can be recorded to a video recorder (e.g.,
VCR, DVR) connected to the VCR/DVR OUT jacks.
See pages 26 to 40 for hookup information.
Note:
• If you select a different input source during recording,
that input source will be recorded instead.
You can overdub audio onto your video recordings by
simultaneously recording audio and video from two sep-
arate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player con-
nected to the CD IN and video from the camcorder con-
nected to the AUX INPUT VIDEO jack are recorded by
the VCR connected to the VCR/DVR OUT jacks.
simultaneously recording audio and video from two sep-
arate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player con-
nected to the CD IN and video from the camcorder con-
nected to the AUX INPUT VIDEO jack are recorded by
the VCR connected to the VCR/DVR OUT jacks.
Recording the Input Source
1
Use the input selector buttons to
select the source that you want
to record.
select the source that you want
to record.
See “Which Connections Should I
Use?” on page 27 to see which signals
can be output and recorded.
Use?” on page 27 to see which signals
can be output and recorded.
You can watch the source while record-
ing it. The AV receiver’s MASTER
VOLUME control has no effect on
recording.
ing it. The AV receiver’s MASTER
VOLUME control has no effect on
recording.
2
On your recorder, start record-
ing.
ing.
3
On the source component, start
playback.
playback.
DVD
VCR/DVR CBL/SAT
AUX
TAPE
TUNER
CD
Remote
controller
Recording from Different AV Sources
1
Prepare the camcorder and CD player for
playback.
playback.
2
Prepare the VCR for recording.
3
Press the [AUX] input selector button.
4
Press the [CD] input selector button.
This selects the CD player as the audio source but
leaves the camcorder as the video source.
leaves the camcorder as the video source.
5
Start recording on the VCR, then start
playback on the camcorder and CD player.
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD
player are recorded by the VCR.
player are recorded by the VCR.
IN
IN
IN
IN
IN
IN
IN
IN 1(DVD)
OUT
OUT
COMPONENT VIDEO
Y
C
B/
P
B
C
R/
P
R
SUB
WOOFER
FRONT
SURR
SURR BACK
CENTER
CD
R
L
TAPE
CBL/SAT
CBL/SAT
VCR/DVR
VCR/DVR
DVD
DVD
R
L
R
L
S
V
MONITOR
OUT
S
V
REMOTE
CONTROL
ASSIGNABLE
COAXIAL
OPTICAL
1
(DVD)
2
(CBL/SAT)
1
(VCR/DVR)
2
(CD)
DIGITAL IN
ASSIGNABLE
ANTENNA
FM
AM
75
OUT
OUT
HDMI
IN 4
IN 3
(CBL/SAT)
(VCR/DVR)
(DVD)
IN 2
IN 1
ASSIGNABLE
OUT
IN 2 (CBL/SAT)
DOCK
(for DS-A1L)
VIDEO
L AUDIO R
AUX INPUT
Camcorder
VCR
CD player
video signal
audio signal
audio signal
HT-S6100_En.book Page 68 Tuesday, July 1, 2008 4:58 PM