ONKYO SKF-750XF L Manual Do Utilizador
48
First Time Setup
—Continued
Notes:
• When an HDMI IN is assigned to an input selector in
“HDMI Input Setup” on page 46, this input assign-
ment is automatically set to the same HDMI IN. And
in addition to the usual inputs (e.g., COAX1, COAX2,
etc.), you can also select HDMI inputs. If you change
the input assignment from an HDMI IN to one of the
other inputs (e.g., COAX1 or COAX2), be sure to set
ment is automatically set to the same HDMI IN. And
in addition to the usual inputs (e.g., COAX1, COAX2,
etc.), you can also select HDMI inputs. If you change
the input assignment from an HDMI IN to one of the
other inputs (e.g., COAX1 or COAX2), be sure to set
the“Automatic Audio Input Selection Setup” on
page 49 to the same input (e.g., COAX1 (Auto) or
COAX2 (Auto)).
page 49 to the same input (e.g., COAX1 (Auto) or
COAX2 (Auto)).
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
buttons.
If you connect an
-capable Onkyo MiniDisc recorder
or CD recorder to the TAPE IN/OUT jacks, for
to
work properly, you must change this setting.
This setting can only be changed on the AV receiver.
2
Use the Up and Down [
]/[
]
buttons to select “1. Input
Assign,” and then press
[ENTER].
Assign,” and then press
[ENTER].
3
Use the Up and Down [
]/[
]
buttons to select “3. Digital
Audio Input,” and then press
[ENTER].
Audio Input,” and then press
[ENTER].
4
Use the Up and Down [
]/[
]
buttons to select an input selec-
tor, and then use the Left and
Right [
tor, and then use the Left and
Right [
]/[
] buttons to select:
COAX1
: Select if the component is
connected to DIGITAL IN
COAXIAL 1.
COAXIAL 1.
COAX2
: Select if the component is
connected to DIGITAL IN
COAXIAL 2.
COAXIAL 2.
OPT1
: Select if the component is
connected to DIGITAL IN
OPTICAL 1.
OPTICAL 1.
OPT2
: Select if the component is
connected to DIGITAL IN
OPTICAL 2.
OPTICAL 2.
- - - - -:
Select if the component is
connected to an analog
input.
connected to an analog
input.
5
Press the [SETUP] button.
Setup closes.
Changing the Input Display
1
Press the [TAPE] input selector
button so that “TAPE” appears
on the display.
button so that “TAPE” appears
on the display.
2
Press and hold down the [TAPE]
input selector button (about 3
seconds) to change the setting.
input selector button (about 3
seconds) to change the setting.
Repeat this step to select MD or CDR.
For the TAPE input selector, the setting
changes in this order:
changes in this order:
ON/STANDBY
STANDBY
SPEAKERS
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY
DIMMER
MEMORY
CLEAR
DIGITAL INPUT
TUNING MODE
B
A
PHONES
MULTI CH
DOCK
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
SETUP MIC
VIDEO
L AUDIO R
AUX INPUT
ENTER
RETURN
TUNING
PRESET
MASTER VOLUME
AV RECEIVER
HT-R667
LISTENING MODE
1, 2
TAPE
TAPE
TAPE
→
MD
→
CDR
→
HT-S6100_En.book Page 48 Tuesday, July 1, 2008 4:58 PM