Roland Fantom-X8 Manual Do Utilizador
114
Creating a Performance
The Fantom-X lets you assign the parameters that will be affected
when you operate the realtime control knobs, assignable switches, D
Beam, pitch bend, or modulation lever. This lets you modify the
sound in a variety of ways by operating the controllers.
when you operate the realtime control knobs, assignable switches, D
Beam, pitch bend, or modulation lever. This lets you modify the
sound in a variety of ways by operating the controllers.
1.
Access the Performance Layer or Mixer screen, and select
the Performance whose settings you wish to modify (p. 99).
the Performance whose settings you wish to modify (p. 99).
If you want to create a performance from scratch (rather than
starting from an existing performance), execute the
starting from an existing performance), execute the
Initialize
2.
Press [F4 (Ctrl Setting)].
The Control Setting (Performance) screen appears.
fig.09-011_50
3.
The parameters are organized into several editing groups.
Press [F1 (
Press [F1 (
⇑
)] [F2 (
⇓
)] to select the tab for the editing group
that contains the parameter you wish to edit.
4.
Use [CURSOR] to move the cursor to the parameter you
wish to modify.
wish to modify.
5.
Turn the VALUE dial or press [INC]/[DEC] to get the value
you want.
you want.
6.
Repeat steps 3-5 to set each parameter you want to edit.
7.
The settings for the Solo Synth are saved for the system
settings. Press [F8 (System Write)] to execute the write
operation.
settings. Press [F8 (System Write)] to execute the write
operation.
8.
The settings in the Control Setting screen are saved
independently for each performance. If you wish to save the
changes you’ve made, press [WRITE] to perform the Save
operation (p. 120). If you do not wish to save changes,
press [EXIT] to return to the Performance Layer or Mixer
screen.
independently for each performance. If you wish to save the
changes you’ve made, press [WRITE] to perform the Save
operation (p. 120). If you do not wish to save changes,
press [EXIT] to return to the Performance Layer or Mixer
screen.
If you return to the Performance PLAY screen without saving,
the display will indicate “*,” reminding you that the
Performance settings have been modified.
the display will indicate “*,” reminding you that the
Performance settings have been modified.
If you turn off the power or select a different sound while the
display indicates “*,” your edited Performance will be lost.
display indicates “*,” your edited Performance will be lost.
fig.09-013_50
For details on these settings, refer to
D Beam (Pad Trigger)
Instead of striking the pads themselves, you can also use the D Beam
controller to control the sounding of the pads.
controller to control the sounding of the pads.
PAD trigger settings are saved independently for each
performance as part of the performance settings. This lets you
create performances that make effective use of controller
settings.
performance as part of the performance settings. This lets you
create performances that make effective use of controller
settings.
Pad Number
Specifies the pad number affected by the D Beam.
Value:
1–16
Pad Velocity
Specifies the strength of the pad sound played by the D Beam
controller.
controller.
Value:
1–127
Pad Control Mode
This specifies how the D Beam will behave when it is obstructed. If
this is set to MOMENTARY, the parameter will be on only while the
D Beam is obstructed, and will turn off when you stop obstructing it.
If this is set to LATCH, the parameter will alternately be switched
on/off each time you obstruct the D Beam.
this is set to MOMENTARY, the parameter will be on only while the
D Beam is obstructed, and will turn off when you stop obstructing it.
If this is set to LATCH, the parameter will alternately be switched
on/off each time you obstruct the D Beam.
Value:
MOMENTARY, LATCH
Selecting the Parameter
Controlled by the Realtime
Controllers or D Beam
Controller (Control Setting)
Make Settings for the Realtime
Controllers and D Beam Controller
(Ctrl)
Fantom-X678_r_e.book 114 ページ ２００５年５月１２日 木曜日 午後４時４０分