Roland Fantom-X8 Manual Do Utilizador
156
Editing a Sample
This operation raises the level of the entire sample as much as
possible without exceeding the maximum level. In some cases, the
volume of a phrase you resampled (p. 143) will be lower than the
volume of the original phrase. In this case, it is a good idea to boost
the volume by executing the Normalize operation.
possible without exceeding the maximum level. In some cases, the
volume of a phrase you resampled (p. 143) will be lower than the
volume of the original phrase. In this case, it is a good idea to boost
the volume by executing the Normalize operation.
*
You cannot execute this with more than one sample selected.
1.
Press [SAMPLE EDIT] to access the Sample Edit screen.
2.
Press [F3 (Sample Modify)] to access the Sample Modify
window.
window.
3.
Press [F3 (Normalize)].
fig.15-018_50
4.
If you want to replace the current sample with the
normalized sample, press [F6 (Over Write)] to display the
“
normalized sample, press [F6 (Over Write)] to display the
“
✔
” symbol.
5.
Press [F8 (Exec)].
A message will ask you for confirmation.
6.
To execute, press [F8 (Exec)].
*
To cancel, press [F7 (Cancel)].
This operation applies an envelope (time-variant change) to the
volume of the sample.You can also adjust the volume of the entire
sample.
volume of the sample.You can also adjust the volume of the entire
sample.
*
You cannot execute this with more than one sample selected.
1.
Press [SAMPLE EDIT] to access the Sample Edit screen.
2.
Press [F3 (Sample Modify)] to access the Sample Modify
window.
window.
3.
Press [F4 (Amp)].
fig.15-019_50
4.
Use VALUE dial or [INC] [DEC] to set the value.
•
Rate 1–4:
Specifies the rate of volume boost.
This specifies how much boost will be applied relative to the
current volume. The entire sample you select will be boosted.
current volume. The entire sample you select will be boosted.
Value:
0–400%
5.
If you want to specify a point, press [F5 (Point)] to light it
into red. Press
into red. Press
or
to select a parameter, and then
use VALUE dial or [INC] [DEC] to set the value.
•
Current Point:
Specifies the currently selected point. Beginning
near the start point, the points will be numbered 1, 2, 3, or 4.
•
Point 1–4:
Location of the current point
•
Rate 1–4:
Amplification ratio of the current point
Specifies how the volume of each point is to be boosted relative
to the current value.
to the current value.
Value:
0–400%
6.
If you want the edited sample to replace the current sample,
press [F6 (Over Write)] to display the “
press [F6 (Over Write)] to display the “
✔
” mark.
7.
Press [F8 (Exec)].
A message will ask you for confirmation.
8.
To execute, press [F8 (Exec)].
*
To cancel, press [F7 (Cancel)].
This operation stretches or shrinks the sample to modify the length
or tempo. You can stretch or shrink the sample by a factor of one half
to double the original length.
or tempo. You can stretch or shrink the sample by a factor of one half
to double the original length.
*
You cannot execute this with more than one sample selected.
1.
Press [SAMPLE EDIT] to access the Sample Edit screen.
2.
Press [F3 (Sample Modify)] to access the Sample Modify
window.
window.
Maximizing the Volume of a
Sample (Normalize)
Amp
Stretching or Shrinking a
Sample (Time Stretch)
Fantom-X678_r_e.book 156 ページ 2005年5月12日 木曜日 午後4時40分