Roland Fantom-X8 Manual Do Utilizador

 

To cancel, press [F7 (Cancel)].

 

If you decide to discard the changes you made to the system 
exclusive message and return to the Microscope screen, press 
[EXIT].

• In the case of a Roland type IV system exclusive message, the 

checksum can be calculated automatically when you finalize the 
values. If you do not want to calculate the checksum 
automatically, press [F1 (Auto Sum)] to turn off the light.

• When you press [F4 (Test)], the system exclusive message you 

are editing will be transmitted from the MIDI OUT connector.

Phrase tracks or patterns can record the following nine types of 
sequencer data. The recorded location (measure-beat-tick) is 
displayed at the far left of each data item, and the MIDI channel 
number is displayed beside it.

 

These MIDI messages represent notes. From the left, the parameters 
are Note Number, which indicates the name of the note; On Velocity, 
which specifies the force with which the key is pressed; Duration, 
which specifies the duration of the note; and Off Velocity, which 
determines the speed with which the key is released.

 

This MIDI message switches sounds. The program number (PC#) 
selects the sound.

 

This MIDI message applies various effects such as modulation or 
expression. The controller number (CC#) selects the function, and 
Value specifies the depth of the effect.

 

For the function corresponding to each controller number, refer 
to 

 

 

This MIDI message changes the pitch. The value specifies the 
amount of pitch change.

 

This MIDI messages applies aftertouch to an individual note. From 
the left, the parameters are Note Number which specifies the key, 
and Value which specifies the depth of the aftertouch.

 

This MIDI message applies aftertouch to an entire MIDI channel. 
Value specifies the depth of the aftertouch.

 

These are MIDI messages used to make settings unique to the 
Fantom-X, such as sound settings. Input the data between “F0” and 
“F7.”

 

For details on system exclusive messages, refer to 

 

 

This MIDI message causes an analog synthesizer to tune itself.

 

This is data that causes a pattern to play back. Use the Number 
parameter to select the pattern number. The pattern name is shown 
in parentheses ( ), and the location at which the pattern will finish 
playing is shown at the right of the “->” symbol.

 

If the pattern called by the Pattern Call message extends beyond 
the last measure of the song, the pattern playback will be 
interrupted at that point.

• Only one pattern can be played at a time by Pattern Call 

messages in a given phrase track. This means that if a Pattern 
Call message is recorded at a location before the previous 
pattern has finished playing, the pattern that was playing will 
be interrupted, and the next pattern will begin playing. If more 
than one Pattern Call message is recorded at the same location, 
the message that is displayed last in the Microscope screen will 
be played.

• Although it is possible to record Pattern Call messages in a 

pattern, they will not be played. If you want to place the data of 
another pattern into a pattern, use Track Edit to copy the data.

 

The Tempo track records tempo data for the song.

 

This data specifies the tempo. The song will play back according to 
the “Value” of the tempo change.

The value displayed in “

=**” is the tempo at which the song will 

actually play (the playback tempo), and can be changed only in the 
PLAY screen of each mode.

If the tempo change value differs from the playback tempo, this 
means that the playback tempo has been changed temporarily. In 
other words, since the tempo change value has not been rewritten, 
this setting will be lost if you select another song or turn off the 
power. If you want to play back at this tempo the next time as well, 
you must re-save the song to disk. This will rewrite the tempo 
change value so that it matches the playback tempo.

Fantom-X678_r_e.book 193 ページ ２００５年５月１２日　木曜日　午後４時４０分