Roland Fantom-X8 Manual Do Utilizador
210
Adding Effects
In Performance mode you can use three multi-effects (MFX1, MFX2,
MFX3), one chorus, and one reverb. For each of the three multi-
effects, the chorus, and the reverb, you can specify whether it will
operate according to the effect settings of the performance, or
according to the effect settings of the patch or rhythm set assigned to
the part you specify. The three multi-effects can be used
independently, or you can connect two or three of them in series.
MFX3), one chorus, and one reverb. For each of the three multi-
effects, the chorus, and the reverb, you can specify whether it will
operate according to the effect settings of the performance, or
according to the effect settings of the patch or rhythm set assigned to
the part you specify. The three multi-effects can be used
independently, or you can connect two or three of them in series.
Here you can make overall settings for effects, and the output
destination and level of each signal.
destination and level of each signal.
fig.22-006.eps_50
fig.22-007
Part Select
Select the part for which you want to make settings.
Value:
1–16
Part Output Assign
Specifies for each part how the direct sound will be output.
Value
MFX:
Output in stereo through multi-effects. You can also
apply chorus or reverb to the sound that passes
through multi-effects.
apply chorus or reverb to the sound that passes
through multi-effects.
A, B:
Output to the OUTPUT A (MIX) jack or OUTPUT B
jack in stereo without passing through multi-effects.
jack in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono
without passing through multi-effects.
without passing through multi-effects.
PAT:
The part’s output destination is determined by the
settings of the patch or rhythm set assigned to the
part.
settings of the patch or rhythm set assigned to the
part.
If you've made settings so that sounds are separately routed to
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug
is actually inserted in the INDIVIDUAL 2 jack, the sounds
routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed
and output from the INDIVIDUAL 1 jack.
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug
is actually inserted in the INDIVIDUAL 2 jack, the sounds
routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed
and output from the INDIVIDUAL 1 jack.
If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 230).
output from the OUTPUT A (MIX) jacks in stereo (p. 230).
If you've set Tone Out Assign to “MFX,” set the MFX Output
Assign parameter (
Assign parameter (
) to specify the output destination of the
sound that has passed through the multi-effects.
• Chorus and reverb are output in mono at all times.
• The output destination of the signal after passing through the
chorus is set with the Chorus Output Select (
) and the
Chorus Output Assign (
).
• The output destination of the signal after passing through the
reverb is set with the reverb Output Assign (
).
Part Output MFX Select (Part Output Multi-
Effects Select)
Of the three systems of multi-effects that can be used
simultaneously, specify which multi-effects will be used.
simultaneously, specify which multi-effects will be used.
Value:
1–3(MFX-1–MFX-3)
Part Output Level
Set the level of the signal that is sent to the output destination
specified by Part Output Assign (
).
Value:
0–127
Part Chorus Send Level
Sets the level of the signal sent to chorus for each part.
Value:
0–127
Applying Effects in
Performance Mode
Specifying How the Sound Will Be
Output (Routing)
Signal Flow Diagram and
Parameters
1
13
10
9
8
11
7
10
9
8
11
7
10
9
8
11
7
14
15
18
12
17
16
6
5
4
2
3
19
20
21
1
2
11
13
15
18
3
4
2
5
Fantom-X678_r_e.book 210 ページ ２００５年５月１２日 木曜日 午後４時４０分