Roland Fantom-X8 Manual Do Utilizador
233
Settings Common to All Modes (System Function)
Sys Ctrl 1–4 Source
System Control Assign selects the MIDI message used as the System
Control.
Control.
Value
OFF:
The system control knob will not be used.
CC01–31, 33–95:
Controller numbers 1–31, 33–95
For details on control change messages, refer to
PITCH BEND:
Pitch Bend
AFTERTOUCH:
Aftertouch
Background Picture
Select the file that is to be displayed as the screen background.
Value:
1–16
Screen Saver Type
Select the type of screen saver.
Value:
1–16
Screen Saver Time
Set the time (minutes) until the screen saver begins working.
If this is OFF, the screen saver will not appear.
Value:
OFF, 5–60 min.
Default File Type
Specifies the file format used when saving a sample.
Value:
WAV, AIFF
Pre Sample Time
The length of sound preceding the moment at which sampling was
manually or automatically initiated that will be captured in the
sample. This lets you prevent the attack portion of the sound from
being omitted from the sample.
manually or automatically initiated that will be captured in the
sample. This lets you prevent the attack portion of the sound from
being omitted from the sample.
Value:
0–1000 ms
Trigger Level
Volume level at which sampling will begin when Auto Trig is ON
A setting of 0 is the minimum.
Value:
0–7
Gap Time
Length of silence at which the sample will be divided
Whenever there is a silent region longer than the specified time, the
sample will be divided at that point, and the next sample number
will be assigned to the sound that follows. This parameter is valid
only when you are using Auto Divide Sampling.
sample will be divided at that point, and the next sample number
will be assigned to the sound that follows. This parameter is valid
only when you are using Auto Divide Sampling.
Value:
500, 1000, 1500, 2000 ms
Input Select
Input source of the external input sound
Value
DIGITAL IN:
DIGITAL INPUT jack
LINE-L-R:
INPUT jacks L/R (stereo)
LINE-L:
INPUT jack L (mono)
MIC:
INPUT jack (mono, mic level)
Trimming Switch
If this is turned on, the Start point and End point settings will be
automatically adjusted after sampling is performed, so any silent
portions at the beginning or end of the sampled sound are excluded.
automatically adjusted after sampling is performed, so any silent
portions at the beginning or end of the sampled sound are excluded.
Value:
OFF, ON
Skip Back Time
Specifies how much earlier in time that you want sampling to take
place when you use Skip Back Sampling. If “OFF” selected, skip-
back sampling cannot be performed.
place when you use Skip Back Sampling. If “OFF” selected, skip-
back sampling cannot be performed.
Value:
OFF, 5s–40s
System Ctrl
Background
Screen Saver
System Control
This function, which departs from previously used methods,
and instead allows you to use MIDI messages to change tone
settings in realtime, is called the Matrix Control (p. 80).
Similarly, the function allowing you to use MIDI messages to
change multi-effects settings in realtime is called the Multi-
effects Control
and instead allows you to use MIDI messages to change tone
settings in realtime, is called the Matrix Control (p. 80).
Similarly, the function allowing you to use MIDI messages to
change multi-effects settings in realtime is called the Multi-
effects Control
Normally, the Matrix Control is used for making patch settings,
and the Multi-effects Control for making settings to patches,
rhythm sets, and performances. However, if you do not need to
change the MIDI messages used for matrix control or multi-
effects control by each patch/rhythm set/performance, or if
you want to use a specific MIDI message for matrix control or
multi-effects control, you will want to make use of System
Control.
and the Multi-effects Control for making settings to patches,
rhythm sets, and performances. However, if you do not need to
change the MIDI messages used for matrix control or multi-
effects control by each patch/rhythm set/performance, or if
you want to use a specific MIDI message for matrix control or
multi-effects control, you will want to make use of System
Control.
In other words, you could call the System Controls
global Matrix Control/Multi-effects Control for the entire
Fantom-X.
Fantom-X.
You can use up to four System Controls.
Sampling
Fantom-X678_r_e.book 233 ページ ２００５年５月１２日 木曜日 午後４時４０分