Yamaha pmn Manual Do Utilizador
E-
30
CONNECTIONS
■ Connecting a front subwoofer
Connect the signal input jack on your subwoofer to the PREOUT/
MAIN IN SUBWOOFER MONO jack.
By connecting two subwoofers to the SUBWOOFER SPLIT jacks,
this unit can reproduce subtle directional changes in the low
frequency sounds.
When you use two subwoofers, connect both of them to the
SUBWOOFER SPLIT jacks using pin plugs.
MAIN IN SUBWOOFER MONO jack.
By connecting two subwoofers to the SUBWOOFER SPLIT jacks,
this unit can reproduce subtle directional changes in the low
frequency sounds.
When you use two subwoofers, connect both of them to the
SUBWOOFER SPLIT jacks using pin plugs.
FRONT
IN
FRONT
OUT
REAR
(
SURROUND)
SUB
WOOFER
SPLIT
MONO
REAR CTR
IN
OUT
REMOTE 1
IN
CTRL
OUT
+12V
10mA
MAX.
RS–
232C
REMOTE 2
CENTER
IN
CENTER
OUT
R
L
PREOUT/MAIN IN
CONTROL
MAIN
IN
MAIN
OUT
R
L
Subwoofer system
Right
Subwoofer system
Left
Subwoofer system
R
L
FRONT
R
L
REAR
CENTER
REAR CENTER
(
SURROUND)
SPEAKERS
Right rear speaker
Left rear speaker
Subwoofer system
■ Impedance selector switch
Select the position whose requirements your speaker system meets.
(Upper position)
Front effect:
The impedance of each speaker must be 6
Ω or
higher.
Rear:
The impedance of each speaker must be 4
Ω or
higher.
Rear Center: The impedance of the speaker must be 4
Ω or higher.
Center:
The impedance of the speaker must be 4
Ω or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 4
of each speaker must be 4
Ω or higher. If you use
two pairs of main speakers, the impedance of each
speaker must be 8
speaker must be 8
Ω or higher.
(Lower position)
Front effect:
The impedance of each speaker must be 8
Ω or
higher.
Rear:
The impedance of each speaker must be 8
Ω or
higher.
Rear Center: The impedance of the speaker must be 8
Ω or higher.
Center:
The impedance of the speaker must be 8
Ω or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 8
of each speaker must be 8
Ω or higher. If you use
two pairs of main speakers, the impedance of each
speaker must be 16
speaker must be 16
Ω or higher.
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SELECTEUR D’IMPEDANCE
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
: 6
ΩMIN. /SPEAKER
: 4
ΩMIN. /SPEAKER
: 4
ΩMIN. /SPEAKER
: 4
ΩMIN. /SPEAKER
: 4
ΩMIN. /SPEAKER
: 8
ΩMIN. /SPEAKER
FRONT
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
REAR
REAR CENTER
CENTER
MAIN A OR B
A + B
: 8
ΩMIN. /SPEAKER
: 8
ΩMIN. /SPEAKER
: 8
ΩMIN. /SPEAKER
: 8
ΩMIN. /SPEAKER
: 8
ΩMIN. /SPEAKER
: 16
ΩMIN. /SPEAKER
AC OUTLETS
AC IN
WARNING
Do not change the IMPEDANCE SELECTOR switch setting
while the power to this unit is on, otherwise this unit may be
damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/
ON SWITCH IS PRESSED:
The IMPEDANCE SELECTOR switch may not be set to either
end. If so, set the switch to either end when this unit is in the
standby mode.
Do not change the IMPEDANCE SELECTOR switch setting
while the power to this unit is on, otherwise this unit may be
damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/
ON SWITCH IS PRESSED:
The IMPEDANCE SELECTOR switch may not be set to either
end. If so, set the switch to either end when this unit is in the
standby mode.
■ Connecting a rear subwoofer
By using both front and rear subwoofers, the CINEMA-DSP sound
field programs can produce realistic movie effects with powerful,
dynamic sound. To take advantage of this dynamic sound, be sure to
set the “1C REAR L/R SP” item in the SET MENU to “LARGE”
(see page __).
field programs can produce realistic movie effects with powerful,
dynamic sound. To take advantage of this dynamic sound, be sure to
set the “1C REAR L/R SP” item in the SET MENU to “LARGE”
(see page __).
Caution
• Adjust the speaker volume for the subwoofer with the controls on
the subwoofers, not on this unit.