Yamaha RX-V359 Manual Do Utilizador
33
SOUND FIELD PROGRAMS
BA
S
IC
OPE
R
A
T
IO
N
English
For 2CH STEREO:
Direct
DIRECT
Function:
2-channel stereo direct. Bypasses the
decoders and DSP processors of this unit
for pure hi-fi stereo sound when playing
2-channel analog sources.
decoders and DSP processors of this unit
for pure hi-fi stereo sound when playing
2-channel analog sources.
Choices:
AUTO
, OFF
y
• The “AUTO” setting bypasses the decoders and DSP processors
only when “BASS” and “TREBLE” are set to 0 dB (see
page 24).
page 24).
• When multi-channel signals (Dolby Digital and DTS) are input,
they are downmixed to 2 channels and output from the front left
and right speakers.
and right speakers.
• The low-frequency signals input from the front left and right
speakers are redirected to the subwoofer in the following cases:
– “BASS” is set to “BOTH” (see page 54).
– “FRONT” is set to “SML” (see page 54) and “BASS” is set to
– “BASS” is set to “BOTH” (see page 54).
– “FRONT” is set to “SML” (see page 54) and “BASS” is set to
For PRO LOGIC II Music:
Panorama
PANORAMA
Function:
Sends stereo signals to the surround
speakers as well as the front speakers for
a wraparound effect.
speakers as well as the front speakers for
a wraparound effect.
Choices:
OFF
, ON
Dimension
DIMENSION
Function:
Gradually adjusts the sound field either
towards the front or towards the rear.
towards the front or towards the rear.
Control range:
–3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
front), initial setting is STD (standard).
Center width
CT WIDTH
Function:
Adjusts the center image from all three
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
Control range:
0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
■
Using Virtual CINEMA DSP
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers by creating
virtual speakers.
If you set “SURR”
DSP programs without surround speakers by creating
virtual speakers.
If you set “SURR”
to “
NONE” (see page 54), Virtual
CINEMA DSP activates automatically whenever you
select a CINEMA DSP program (see page 31).
select a CINEMA DSP program (see page 31).
Virtual CINEMA DSP will not activate even when “SURR” is set
to “NONE” (see page 54) in the following cases:
to “NONE” (see page 54) in the following cases:
– When “2CH STEREO” (see page 31) is selected or when this
unit is in the “STRAIGHT” mode.
– When the component connected to the MULTI CH INPUT
jacks is selected as the input source (see page 25).
– When headphones are connected to the PHONES jack.
■
Listening to unprocessed input signals
When this unit is in the “STRAIGHT” mode, multi-
channel sources are decoded straight into the appropriate
channels without any additional effect processing. 2-
channel stereo sources are output from only the front left
and right speakers.
channel sources are decoded straight into the appropriate
channels without any additional effect processing. 2-
channel stereo sources are output from only the front left
and right speakers.
1
Press AMP on the remote control and then
STRAIGHT to select “STRAIGHT”.
STRAIGHT to select “STRAIGHT”.
2
To deactivate the “STRAIGHT” mode, press
STRAIGHT on the remote control again so
that “STRAIGHT” disappears from the front
panel display.
STRAIGHT on the remote control again so
that “STRAIGHT” disappears from the front
panel display.
The sound field program is turned back on.
y
You can also select “STRAIGHT” by pressing STRAIGHT
on the front panel.
on the front panel.
Note
ENT.
STRAIGHT
AMP