ONKYO TX-SR8467 Manual Do Utilizador
68
Advanced Setup
—Continued
Low-Pass Filter for the LFE Channel
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting in step 3 is set to Yes, and the
Front setting in step 4 is set to Full Band.
In the speaker setup screen, you can choose how bass
information is distributed to your speakers only if you
have large front left and right speakers AND a subwoofer.
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting in step 3 is set to Yes, and the
Front setting in step 4 is set to Full Band.
In the speaker setup screen, you can choose how bass
information is distributed to your speakers only if you
have large front left and right speakers AND a subwoofer.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
6
Use the Up and Down [
]/[
]
buttons to select “d. Surround,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select a
crossover frequency.
If no surround left and right speakers
are connected, select None.
are connected, select None.
Note:
If the Front setting in step 4 is set to
anything other than Full Band, Full
Band cannot be selected here.
If the Front setting in step 4 is set to
anything other than Full Band, Full
Band cannot be selected here.
7
Use the Up and Down [
]/[
]
buttons to select “e. SurrBack,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select a
crossover frequency.
If no surround back speakers are con-
nected, select None.
nected, select None.
Notes:
• If the Surround setting in step 6 is set
• If the Surround setting in step 6 is set
to None, this setting cannot be
selected.
selected.
• If the Surround setting in step 6 is set
to anything other than Full Band,
Full Band cannot be selected here.
Full Band cannot be selected here.
8
Use the Up and Down [
]/[
]
buttons to select “f. SurrBack
Ch,” and then use the Left and
Right [
Ch,” and then use the Left and
Right [
]/[
] buttons to select:
1ch: Select if one surround back
speaker is connected.
2ch: Select if two (left and right)
surround back speakers are
connected.
connected.
Note:
If the Surround Back Setting in step 7 is
set to None, this setting cannot be
selected.
If the Surround Back Setting in step 7 is
set to None, this setting cannot be
selected.
Continue with step 9 in the right col-
umn.
umn.
9
Use the Up and Down [
]/[
]
buttons to select “g. LPFofLFE,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select a low-
pass filter frequency.
The following low-pass filter frequen-
cies can be selected: 80 Hz, 100 Hz,
120 Hz (default), 150 Hz, or 200 Hz.
Continue with step 10 below.
cies can be selected: 80 Hz, 100 Hz,
120 Hz (default), 150 Hz, or 200 Hz.
Continue with step 10 below.
10
Use the Up and Down [
]/[
]
buttons to select “h. Double
Bass,” and then use the Left and
Right [
Bass,” and then use the Left and
Right [
]/[
] buttons to select:
On: Double Bass function on
(default). Front left and right
bass also goes to the sub-
woofer simultaneously.
bass also goes to the sub-
woofer simultaneously.
Off: Double Bass function off.
11
Press the [SETUP] button.
The setup menu closes.
This setting is not set automatically by the Automatic
Speaker Setup function (see page 38).
Speaker Setup function (see page 38).
This setting is not set automatically by the Automatic
Speaker Setup function (see page 38).
Speaker Setup function (see page 38).
SETUP