ONKYO TX-SR502E Manual Do Utilizador
46
Advanced Function
These functions only work with speaker set A.
Audio Adjust provides various functions for adjusting
the sound.
Audio Adjust provides various functions for adjusting
the sound.
The Audio Adjust functions are explained below.
■
Double Bass
The Double Bass function boosts the bass by feeding
bass sounds from the front left and right channels to the
subwoofer. To use this function, in the Speaker Configu-
ration, the Subwoofer setting must be set to Yes and the
Front setting must be set to Large (see page 32).
The Double Bass function works well with mono and 2-
channel sources, including 96 kHz PCM.
bass sounds from the front left and right channels to the
subwoofer. To use this function, in the Speaker Configu-
ration, the Subwoofer setting must be set to Yes and the
Front setting must be set to Large (see page 32).
The Double Bass function works well with mono and 2-
channel sources, including 96 kHz PCM.
On:
Double Bass function on.
Off:
Double Bass function off.
■
Late Night (Dolby Digital only)
With this function you can reduce the dynamic range of
Dolby Digital material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want to
disturb anyone.
Dolby Digital material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want to
disturb anyone.
Off:
Late Night function off.
Low:
Small reduction in dynamic range.
High:
Big reduction in dynamic range.
Note that the effect of the Late Night function depends
on the Dolby Digital material that you are playing, and
with some material there will be little or no effect.
This function is turned off when the TX-SR502/
TX-SR502E is set to Standby.
on the Dolby Digital material that you are playing, and
with some material there will be little or no effect.
This function is turned off when the TX-SR502/
TX-SR502E is set to Standby.
Tip:
You can also set this function by using the remote
controller’s [L NIGHT] button.
■
CinemaFILTER
With this function, you can soften the harshness, or
brightness sometimes experienced with movie
soundtracks, which are typically mixed for reproduction
in a movie theater.
brightness sometimes experienced with movie
soundtracks, which are typically mixed for reproduction
in a movie theater.
You can set the CinemaFILTER function to
On
or
Off
.
The CinemaFILTER function can be used with the fol-
lowing listening modes: Dolby Digital, Dolby Digital
EX, Dolby Pro Logic II Movie, Dolby Pro Logic IIx
Movie, DTS, DTS-ES, DTS NEO:6 Cinema, DTS 96/
24, DTS+Neo:6, and DTS+Dolby EX.
lowing listening modes: Dolby Digital, Dolby Digital
EX, Dolby Pro Logic II Movie, Dolby Pro Logic IIx
Movie, DTS, DTS-ES, DTS NEO:6 Cinema, DTS 96/
24, DTS+Neo:6, and DTS+Dolby EX.
Tip:
You can also set this function by using the remote
controller’s [CINE FLTR] button.
Adjusting the DTS Neo:6 Music Mode
■
Center Image
DTS Neo:6 derives a center-channel signal from stereo
material, either analog or digital. In Music mode, the
center speaker is intended to augment the left and right
speakers, allowing them to faithfully reproduce the orig-
inal stereo mix. For this reason, the center channel sound
is not fully subtracted from the left and right channels.
With this function, you can adjust the amount of subtrac-
tion depending on your room layout and personal prefer-
ence.
material, either analog or digital. In Music mode, the
center speaker is intended to augment the left and right
speakers, allowing them to faithfully reproduce the orig-
inal stereo mix. For this reason, the center channel sound
is not fully subtracted from the left and right channels.
With this function, you can adjust the amount of subtrac-
tion depending on your room layout and personal prefer-
ence.
Using the Audio Adjust Functions
1
Press the [SETUP] button.
2
Use the Up and Down [
]/[
]
buttons to select “4. Audio
Adjust,” and then press the
[ENTER] button.
Adjust,” and then press the
[ENTER] button.
3
Use the Left and Right [
]/[
]
buttons to select the settings.
4
Press the Down [
] button to
select the next setting.
5
Repeat steps 3 and 4 to complete
all settings.
all settings.
6
Press the [SETUP] button.
Setup closes.
ENTER
SET
UP
GUI
DE
RE
TURN
EXIT
CINE FLTR
LEVEL
-
LEVEL
+
CH SEL
TEST TONE
DSP
DIRECT
STEREO
ALL ST
SURR
L NIGHT
TO
P M
ENU
MEN
U
VOL
+
-
CDR
SAT
AMP
+
_
TV
VCR
CABLE
DVD
CD
MD
DISC
CH
TONE
TUNER/
TAPE
TAPE
DISPLAY
TV
INPUT
INPUT
PREV
CH
CH
DIMMER
SLEEP
RANDOM
SP A
SP B
MUTING
ANGLE
SEARCH
SUBTITLE
AUDIO
MEMORY
A-B
REPEAT
RC-567M
REC
LAST M
REMOTE MODE
OPEN/CLOSE
DSP
VIDEO OFF
LEVEL
-
LEVEL
+
SETUP
CINE FLTR
ENTER
L NIGHT
ENTER
ENTER
ENTER
ENTER
TX-SR502_En.book Page 46 Tuesday, February 17, 2004 12:14 PM