ONKYO TX-SR502 Manual Do Utilizador
36
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
stations. You can store your favorite stations as presets
for quick selection.
Setting the AM Tuning Interval
(Worldwide model only)
If you’re using the Worldwide model (i.e., your AV
Receiver has a VOLTAGE SELECTOR on the rear
panel), you need to set the AM tuning interval for com-
patibility with AM broadcasts in your particular country.
The initial setting is 9 kHz.
North America: 10 kHz
Other countries: 9 kHz
Receiver has a VOLTAGE SELECTOR on the rear
panel), you need to set the AM tuning interval for com-
patibility with AM broadcasts in your particular country.
The initial setting is 9 kHz.
North America: 10 kHz
Other countries: 9 kHz
Note:
All presets will be deleted when you change the AM tun-
ing interval.
ing interval.
■
Auto Tuning Mode
When tuned into an FM station, the TUNED and FM
STEREO indicators appear on the display, as shown.
When tuned into an AM station, the TUNED indicator
appears.
STEREO indicators appear on the display, as shown.
When tuned into an AM station, the TUNED indicator
appears.
Using RDS (European model only)
When tuned into an RDS (Radio Data System) station
that’s broadcasting PS (Program Service Name) infor-
mation, the RDS indicator appears, and the name of the
station appears on the display. Only European models
support RDS, and only in areas where RDS is used.
that’s broadcasting PS (Program Service Name) infor-
mation, the RDS indicator appears, and the name of the
station appears on the display. Only European models
support RDS, and only in areas where RDS is used.
■
Manual Tuning Mode
The American model changes FM frequency in 0.1 MHz
steps, 10 kHz steps for AM. For other models it’s
0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Switch back to Auto Tuning mode for stereo.
steps, 10 kHz steps for AM. For other models it’s
0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Switch back to Auto Tuning mode for stereo.
Tuning into weak FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Listening to the Radio
1
Use the [TUNER] input selector
button to select either AM or FM.
button to select either AM or FM.
In this example, FM has been selected.
To set the AM tuning interval,
while holding down the [TUNER]
button, press the [MEMORY] but-
ton.
while holding down the [TUNER]
button, press the [MEMORY] but-
ton.
STANDBY/ON
PHONES
STANDBY
DISPLAY
TONE
TUNING MODE
DIGITAL INPUT
LISTENING
MODE
STEREO
MEMORY
RETURN
SETUP
VIDEO
2
TAPE
TUNER
C D
VIDEO
3
DVD
VIDEO
1
VCR
MULTI CH
MASTER VOLUME
TUNING
ENTER
PRESET
S VIDEO
VIDEO
AUDIO
L
R
VIDEO
3 INPUT
CLEAR
SPEAKERS B
A
TUNER
MEMORY
TUNING MODE
MASTER VOLUME
TUNING
PRESET
DISPLAY
TUNER
Band
Frequency
TUNER
TUNING MODE
MEMORY
CLEAR
Tuning into Radio Stations
1
Press the [TUNING MODE] button
so that the AUTO indicator
appears on the display.
so that the AUTO indicator
appears on the display.
2
Press the TUNING Up or Down
[
[
]/[
] button.
Searching stops when a station is
found.
found.
1
Press the [TUNING MODE] button
so that the AUTO indicator disap-
pears from the display.
so that the AUTO indicator disap-
pears from the display.
2
Press and hold the TUNING Up or
Down [
Down [
]/[
] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
TUNING MODE
MEMORY
CLEAR
TUNING
TUNED
AUTO
FM STEREO
TUNING MODE
MEMORY
CLEAR
TUNING
TX-SR502_En.book Page 36 Friday, March 12, 2004 1:05 PM