ONKYO TX-SR701 Manual Do Utilizador
55
Hardware Setup
To display the Hardware Config menu:
1. Display the main menu.
2. Use the
and
cursor buttons to select “1. Hardware
Config” and then press the ENTER button. The “Hardware
Config” menu appears.
Config” menu appears.
a. Surr/Zone 2
If you connect the Zone 2 speakers to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT (TX-
SR701/701E only) terminals, set the Surr/Zone 2 setting to “Zone
2.”
If you connect the Zone 2 speakers to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT (TX-
SR701/701E only) terminals, set the Surr/Zone 2 setting to “Zone
2.”
Surr: In this setting, sound will not be output from the Zone 2
speakers which is connected to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT
(TX-SR701/701E only) terminals. In the main room, 6.1-
channel playback will always be available.
speakers which is connected to the ZONE 2 SPEAKERS
terminals or the amplifier connected to the ZONE 2 PRE OUT
(TX-SR701/701E only) terminals. In the main room, 6.1-
channel playback will always be available.
Zone 2: In this setting, when you are not using the Zone 2, 6.1-
channel playback will be available for the main room. However,
while you use the Zone 2, 6.1-channel playback will not be
available for the main room (2ch stereo playback only).
channel playback will be available for the main room. However,
while you use the Zone 2, 6.1-channel playback will not be
available for the main room (2ch stereo playback only).
b. Surr Back (TX-SR701/701E only)
Specify whether you use one surround back speaker or two.
Specify whether you use one surround back speaker or two.
1ch: Selects when you connect one surround back speaker to
the SURROUND BACK SPEAKER terminals on the TX-
SR701/701E.
the SURROUND BACK SPEAKER terminals on the TX-
SR701/701E.
2ch (PRE OUT): Selects when you connect two surround back
speakers to the power amplifier connected to the SURR BACK
PRE OUT terminals on the TX-SR701/701E.
speakers to the power amplifier connected to the SURR BACK
PRE OUT terminals on the TX-SR701/701E.
Note:
Be sure to use either one or two surround back speakers.
Connecting surround back speakers to both the SURROUND
BACK SPEAKER terminals on the TX-SR701/701E and the power
amplifier will not produce correct surround sound effect.
Be sure to use either one or two surround back speakers.
Connecting surround back speakers to both the SURROUND
BACK SPEAKER terminals on the TX-SR701/701E and the power
amplifier will not produce correct surround sound effect.
c. IR IN Position (TX-SR701/701E)
b. IR IN Position (TX-SR601/601E)
Use this setting when you have a remote control sensor connected
to the IR IN terminal. The setting in this menu tells the TX-SR701/
701E/601/601E whether the remote control sensor is being used for
operation of the TX-SR701/701E/601/601E in the main zone or the
remote zone (Zone 2).
Use this setting when you have a remote control sensor connected
to the IR IN terminal. The setting in this menu tells the TX-SR701/
701E/601/601E whether the remote control sensor is being used for
operation of the TX-SR701/701E/601/601E in the main zone or the
remote zone (Zone 2).
Main: Select when you are using the remote control sensor for
operation with the remote controller in the main zone.
operation with the remote controller in the main zone.
Zone 2: Select when you are using the remote control sensor
for operation with the remote controller in the remote zone
(Zone 2).
for operation with the remote controller in the remote zone
(Zone 2).
Hardware Config
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
1.Hardware Config
***********************
a.Surr/Zone 2:Surr
b.Surr Back : 1ch
c.IR IN Position
:Main
d.TV Format :Auto
e.AM Frequency Step
:9kHz
***********************
a.Surr/Zone 2:Surr
b.Surr Back : 1ch
c.IR IN Position
:Main
d.TV Format :Auto
e.AM Frequency Step
:9kHz
Quit:|SETUP|
TX-SR701/701E
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
1.Hardware Config
***********************
a.Surr/Zone 2 :Surr
b.IR IN Position
:Main
c.TV Format :Auto
d.AM Frequency Step
:9kHz
***********************
a.Surr/Zone 2 :Surr
b.IR IN Position
:Main
c.TV Format :Auto
d.AM Frequency Step
:9kHz
Quit:|SETUP|
TX-SR601/601E
d. TV Format (TX-SR701/701E)
c. TV Format (TX-SR601/601E)
c. TV Format (TX-SR601/601E)
(For all models other than USA and Canadian models)
The default setting is “Auto,” which means that the television
format is detected and automatically set by the TX-SR701/701E/
601/601E. However, if you know the correct format, you can use
this setting to choose either PAL or NTSC so that no time is wasted
on detection.
The default setting is “Auto,” which means that the television
format is detected and automatically set by the TX-SR701/701E/
601/601E. However, if you know the correct format, you can use
this setting to choose either PAL or NTSC so that no time is wasted
on detection.
e. AM Frequency Step (TX-SR701/701E)
d. AM Frequency Step (TX-SR601/601E)
This setting only appears on the worldwide model. It determines the
increment amount or decrement amount when adjusting the AM
tuner frequency. The initial setting is 9 kHz, and this needs only to
be changed if you are using the TX-SR701/701E/601/601E in a 10-
kHz region.
d. AM Frequency Step (TX-SR601/601E)
This setting only appears on the worldwide model. It determines the
increment amount or decrement amount when adjusting the AM
tuner frequency. The initial setting is 9 kHz, and this needs only to
be changed if you are using the TX-SR701/701E/601/601E in a 10-
kHz region.