ONKYO TX-SR604 Manual Do Utilizador
90
Troubleshooting
—Continued
There’s no sound
• Only components connected to analog inputs can be
played in Zone 2.
The sound changes when I connect my head-
phones
phones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (not North American
models).
Mono, Direct, or Pure Audio (not North American
models).
The speaker volume cannot be set as required
• When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as required
• In some cases, corrected values suitable for home the-
ater use may be set automatically.
The display doesn’t work
• The display is turned off when the Pure Audio (not
North American models) listening mode is selected.
How do I change the language of a multiplex
source
source
• Use the “a. Multiplex” setting on the “Audio Adjust”
menu to select Main or Sub (page 73).
The
functions don’t work
• To use
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 36).
nent and AV receiver, even if they are connected digi-
tally (page 36).
The functions Auto Power On/Standby and
Direct Change don’t work for components con-
Direct Change don’t work for components con-
nected via
• These functions don’t work when Zone 2 is turned on.
When performing “Automatic Speaker Setup,”
the measurement fails showing the message
“Ambient noise is too high.”
the measurement fails showing the message
“Ambient noise is too high.”
• This can be caused by any malfunction in your
speaker unit. Check if the unit produces normal
sounds.
sounds.
The following settings can be made for the compo-
nent video, S-Video, and composite video inputs
nent video, S-Video, and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the
tings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
button.
2. Use the Left and Right [
]/[
] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
• Video Attenuation
This setting can be made for the DVD, VIDEO 1,
VIDEO 2, VIDEO 3, or VIDEO 4 input.
If you have a games console connected to the com-
ponent video, S-Video, or composite video input,
and the picture isn’t very clear, you can attenuate the
gain.
VIDEO 2, VIDEO 3, or VIDEO 4 input.
If you have a games console connected to the com-
ponent video, S-Video, or composite video input,
and the picture isn’t very clear, you can attenuate the
gain.
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
Zone 2
Others
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other set-
tings when it’s unplugged or in the case of a power fail-
ure. Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system.
system in order to retain radio presets and other set-
tings when it’s unplugged or in the case of a power fail-
ure. Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
let, set the AV receiver to Standby.