ONKYO TX-DS787 Manual Do Utilizador
65
Programming the commands of remote controllers for other devices into the remote
controller
controller
OPEN/CLOSE
REC
AUDIO
MUTING
DISC
TRACK
DVD
CD
PH
TUN
T2
T1
V1
STEREO
1
2
3
6
5
4
7
+ 10
0
ENT
8
9
SURROUND
THX
DSP
LEVEL +
CH SEL
Re-EQ
LEVEL –
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT
DSP
V2
V3
V –
ENT
OPEN/CLOSE
REC
AUDIO
MUTING
DISC
TRACK
DVD
CD
PH
TUN
T2
T1
V1
STEREO
1
2
3
6
5
4
7
+ 10
0
ENT
8
9
SURROUND
THX
DSP
LEVEL +
CH SEL
Re-EQ
LEVEL –
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT
DSP
V2
V3
V –
ENT
SEND/LEARN
indicator
indicator
MODE
buttons
buttons
SEND/LEARN
indicator
indicator
MODE
buttons
buttons
Erasing the programmed command from one
button
button
You can only erase memorized commands and not preset ones.
1. Press and hold down the desired MODE button
for the command, press the ENT button, and
then release both buttons.
then release both buttons.
When you press the MODE button, the SEND/LEARN
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp lights again and “LEARN”
appears in the display.
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp lights again and “LEARN”
appears in the display.
2. Press and release the button for the command
you wish to erase.
When you press the button, the SEND/LEARN indicator turns
off and “RCV” appears in the display. When you release the
button, the lamp lights again.
off and “RCV” appears in the display. When you release the
button, the lamp lights again.
3. Press and release the same button again.
The SEND/LEARN lamp flashes twice slowly and “CLEAR”
appears in the display. The memorized command is erased.
appears in the display. The memorized command is erased.
Note:
If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, “ERROR” appears in the display, and the remote
controller exits the programming mode. Resume from Step 1.
programming, the SEND/LEARN indicator flashes three times
quickly, “ERROR” appears in the display, and the remote
controller exits the programming mode. Resume from Step 1.
Erasing all the commands programmed under a
MODE button
MODE button
1. Press and hold down the desired MODE
button, press the ENT button twice, and then
release both buttons.
release both buttons.
When you press the MODE button, the SEND/LEARN
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp flashes twice slowly and then
lights again.
indicator lights and that mode appears in the display. When
you press the ENT button, the lamp turns off. When you
release the buttons, the lamp flashes twice slowly and then
lights again.
2. Press and release the same MODE button
again.
When you release the button, the SEND/LEARN indicator
flashes twice slowly. This erases all the commands memorized
to the MODE button.
flashes twice slowly. This erases all the commands memorized
to the MODE button.
Notes:
• If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three
times quickly and the remote controller exits the programming
mode. Resume from Step 1.
times quickly and the remote controller exits the programming
mode. Resume from Step 1.
• If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly,
“ERROR” appears in the display, and the remote controller
exits the programming mode. Resume from Step 1.
“ERROR” appears in the display, and the remote controller
exits the programming mode. Resume from Step 1.
• If many commands have been programmed to the MODE
button, then the SEND/LEARN indicator may remain lit for
some time during Step 2. This is not a malfunction.
some time during Step 2. This is not a malfunction.