ONKYO TX-SR804 Manual Do Utilizador
46
First Time Setup—Continued
If you connect an
-capable Onkyo MiniDisc
recorder, CD recorder, or next generation HDD-compat-
ible component, such as the Remote Interactive Dock, to
the TAPE IN/OUT or VIDEO 3 IN jacks, for
ible component, such as the Remote Interactive Dock, to
the TAPE IN/OUT or VIDEO 3 IN jacks, for
to
work properly, you must change this setting.
This setting can only be changed on the AV receiver.
Note:
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Minimum Speaker Impedance to 4
ohms.
less than 6, set the Minimum Speaker Impedance to 4
ohms.
Note:
Before you change this setting, turn down the volume.
Before you change this setting, turn down the volume.
Notes:
• This procedure can also be performed on the AV
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
and [ENTER] button.
Changing the Input Display
1
Press the [TAPE] or [VIDEO 3]
input selector button so that
“TAPE” or “VIDEO3” appears on
the display.
input selector button so that
“TAPE” or “VIDEO3” appears on
the display.
2
Press and hold down the [TAPE]
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
HDD.
For the TAPE input selector, the setting
changes in this order:
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
HDD.
For the TAPE input selector, the setting
changes in this order:
TAPE
→
MD
→
CDR
→
HDD
→
For the VIDEO 3 input selector, the set-
ting changes in this order:
ting changes in this order:
VIDEO 3
→
HDD
→
VIDEO 3
→
PUSH TO OPEN
STANDBY/ON
STANDBY
MASTER VOLUME
TAPE
ZONE 2
DISPLAY
PURE AUDIO
CD
TUNER
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
DVD
MULTI CH
PHONO
OFF
ON
POWER
1, 2
1, 2
VIDEO 3
or
TAPE
or
TAPE
VIDEO 3
Minimum Speaker Impedance
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “3. Speaker
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “Speaker
Impedance,” and then press
[ENTER].
Impedance,” and then press
[ENTER].
4
Use the Left and Right [
]/[
]
buttons to select:
4 ohms: Select if the impedance of any
4 ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6 ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
5
Press the [SETUP] button.
Setup closes.
Setup closes.
If you change this setting, you must run the automatic
speaker setup again (see page 40).
speaker setup again (see page 40).
RECEIVER
ENTER
ENTER
3.Speaker Setup
------------------------
0.Speaker Impedance
2.Speaker Configuration
3.Speaker Distance
4.Level Calibration
5.THX Audio Setup
6.Equalizer Settings
------------------------
0.Speaker Impedance
2.Speaker Configuration
3.Speaker Distance
4.Level Calibration
5.THX Audio Setup
6.Equalizer Settings
1.Speaker Impedance
ENTER