ONKYO SR805 Manual Do Utilizador
22
Connecting Your Speakers
—Continued
Speaker Connection Precautions
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
between 4 and 16 ohms. If the impedance of any of the
connected speakers is 4 ohms or more but less than 6,
be sure to set the speaker impedance to 4 ohms (see
page 45). If you use speakers with a lower impedance,
and use the amplifier at high volume levels for a long
period of time, the built-in amp protection circuit may
be activated.
connected speakers is 4 ohms or more but less than 6,
be sure to set the speaker impedance to 4 ohms (see
page 45). If you use speakers with a lower impedance,
and use the amplifier at high volume levels for a long
period of time, the built-in amp protection circuit may
be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–) termi-
nals. If you get them the wrong way around, the sound
will be out of phase and will sound unnatural.
and negative (–) terminals to only negative (–) termi-
nals. If you get them the wrong way around, the sound
will be out of phase and will sound unnatural.
• Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
Doing so may damage the AV
receiver.
• Don’t connect more than one
cable to each speaker termi-
nal. Doing so may damage the
AV receiver.
nal. Doing so may damage the
AV receiver.
• Don’t connect a speaker to several terminals.
Connecting the Speaker Cables
The following illustration shows which speaker should be connected to each pair of terminals.
If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.
1
Strip about 5/8" (15
mm) of insulation from
the ends of the
speaker cables, and
twist the bare wires
tightly, as shown.
mm) of insulation from
the ends of the
speaker cables, and
twist the bare wires
tightly, as shown.
2
Unscrew the terminal.
5/8" (15 mm)
3
Fully insert the bare wire.
4
Screw the terminal tight.
FRONT L (BTL)
RS232
DIGITAL
COAXIAL
OPTICAL
REMOTE
CONTROL
CONTROL
IN 1
IN 1
IN 2
IN
IN
IN
IN
PHONO
ZONE2 R
ZONE2 L
FRONT R
FRONT R (BTL)
FRONT L
SURR R
CENTER
SURR L
SURR BACK R
CD
TAPE
AUX 1
GAME/TV
GAME/TV CBL/SAT
CBL/SAT
AUX 1
VCR/DVR
VCR/DVR
DVD
DVD
IR
12V TRIGGER
OUT ZONE 2
OUT ZONE 2
IN
GND
IN 2
IN 3
L
L
V
V
S
S
R
R
ASSIGNABLE
(DVD)
(CBL/SAT)
(VCR/DVR)
(GAME/TV)
(CD)
OUT
HDMI
IN 1
IN 2
IN 3
IN 4
ASSIGNABLE
OUT
COMPONENT VIDEO
ASSIGNABLE
IN 3
Y
CB/PB
CR/PR
IN 2
IN 1(DVD) MONITOR
OUT
OUT
IN
IN
OUT
IN
IN
FRONT
FRONT
CENTER
SUBWOOFER
SUBWOOFER
CENTER
SURR
SURR
ZONE 2
ZONE 3
MULTI CH
PRE OUT
PRE OUT
SURR BACK
SURR BACK
MONITOR
OUT
AM
ANTENNA
FM75
OUT
L
R
AC OUTLET
AC INLET
Bi-AMP
SURR BACK L
Bi-AMP
ZONE 2
OUT
AC 220-240V
SWITCHED
100W 0.45-0.41A MAX.
50/60Hz
FRONT R
FRONT L
SURR R
CENTER
SURR L
SURR BACK R
Bi-AMP
SURR BACK L
Bi-AMP
Surround back
left speaker
Surround back
right speaker
Front left speaker
Front right speaker
Center speaker
Surround right
speaker
Surround left
speaker
TX-SR805_875_En.book Page 22 Thursday, April 26, 2007 3:00 PM