ONKYO SR805 Manual Do Utilizador
45
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
less than 6, set the Speaker Impedance to 4 ohms.
If you’ve connected your front speakers to the FRONT
and SURR BACK terminal posts for bi-amping or
bridging (TX-SR875 only), you must change the
Speaker Type setting. For hookup information, see “Bi-
amping the Front Speakers” on page 23, or “Bridging the
Front Speakers (TX-SR875 only)” on page 24.
and SURR BACK terminal posts for bi-amping or
bridging (TX-SR875 only), you must change the
Speaker Type setting. For hookup information, see “Bi-
amping the Front Speakers” on page 23, or “Bridging the
Front Speakers (TX-SR875 only)” on page 24.
Notes:
• When bridging is used, the AV receiver is able to drive
up to 2.1 speakers in the main room.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the vol-
ume.
Notes:
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
buttons.
• The design of the TX-SR805 and TX-SR875 onscreen
setup menus is slightly different. The TX-SR805
onscreen setup menus are used throughout this
instruction manual.
onscreen setup menus are used throughout this
instruction manual.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “2. Speaker
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
INPUT SELECTOR
DISPLAY
MUTING
GU
IDE
EXI
T
PREV
CH
DIMMER
CDR/MD
SAT
TAPE/AMP
SLEEP
MACRO
REMOTE MODE
--/--- 10
11
12
TV CH
PLAYLIST
RANDOM
AUX
1
AUX
2
GAME/TV
D. TUN
CD
TUNER
TAPE
PHONO
REC
ENTER
TO
P M
ENU
MEN
U
VOL
CH
DISC
ALBUM
TV
VCR
CABLE
DOCK
DVD
RECEIVER
CD
-
1
2
3
ZONE
3
ZONE
2
+
-
+10
0
CLEAR
4
5
6
7
8
9
SE
TUP
RET
UR
N
2, 3
2–5
1
1, 6
If you change these settings, you must run the auto-
matic speaker setup again (see page 55).
matic speaker setup again (see page 55).
RECEIVER
SE
TUP
ENTER
ENTER
3
Use the Up and Down [
]/[
]
buttons to select “1. Speaker Set-
tings,” and then press [ENTER].
tings,” and then press [ENTER].
The Speaker Settings menu appears.
4
Use the Up and Down [
]/[
]
buttons to select “Speaker
Impedance,” and use the Left and
Right [
Impedance,” and use the Left and
Right [
]/[
] buttons to select:
4 ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
speaker is 4 ohms or more but
less than 6.
6 ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
speakers are between 6 and
16 ohms.
5
Use the Up and Down [
]/[
]
buttons to select “Speaker Type,”
and use the Left and Right
[
and use the Left and Right
[
]/[
] buttons to select:
Normal:
Select this if you’ve con-
nected your front speakers
normally.
nected your front speakers
normally.
Bi-Amp:
Select this if you’ve con-
nected your front speakers for
bi-amped operation.
nected your front speakers for
bi-amped operation.
BTL:
(TX-SR875 only) Select this
if you’ve connected your
front speakers for bridged
operation. The BTL indicator
will appear on the display.
if you’ve connected your
front speakers for bridged
operation. The BTL indicator
will appear on the display.
6
Press the [SETUP] button.
Setup closes.
ENTER
ENTER
2-1.Speaker Settings
Speaker Impedance 6ohms
Speakers Type Normal
Speakers Type Normal
ENTER
ENTER
SE
TUP
TX-SR805_875_En.book Page 45 Thursday, April 26, 2007 3:00 PM