Manualsbrain.com
  1. Manuais
  2. Marcas
  3. ONKYO
  4. SR804
  5. Manual Do Utilizador

ONKYO SR804 Manual Do Utilizador

Download
Página de 96
70
Advanced Setup
This section explains how to check the speaker settings 
and how to set them manually, which is useful if you 
change a speaker after performing the automatic speaker 
setup.
Some speaker settings are set automatically by the Auto-
matic Speaker Setup function (see page 40).
Speaker Configuration
With these settings, you can specify which speakers are 
connected and a crossover frequency for each speaker.
The following crossover frequencies can be specified: 
Full Band, 40 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz, 
100 Hz, 120 Hz, 150 Hz, 200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers 
with a good sized woofer. For smaller speakers, specify 
a crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the 
speaker. Refer to your speakers’ manuals to determine 
the optimum crossover frequencies.
If you’re using THX-certified speakers, specify 
80 Hz (THX) for all speakers.
Speaker Setup
1
Press the [RECEIVER] REMOTE 
MODE button, followed by the 
[SETUP] button.
The main menu appears onscreen.
THX
10
- - / - - -
11
12
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD
CD
ZONE2
SAT
TV
VCR
CABLE
MD
CDR
STEREO
SURR
DIRECT
SUBTITLE
AUDIO
ALLST
PLAY MODE
REPEAT
RANDOM
REC
PLAYLIST
-
T V CH
T V VOL
ENTER
SET
UP
TO
P M
ENU
MEN
U
VOL
+
-
CH
DISPLAY
PREV
CH
 DIMMER
SLEEP
MUTING
LISTENING MODE
INPUT SELECTOR
3
2
MACRO
1
+10
0
CLEAR
4
5
6
7
8
9
CD
MULTI CH
DVD
TUNER
PHONO
DISC
ALBUM
V4
TAPE
PURE A
RE
TURN
SETUP
RECEIVER
ENTER
These settings are set automatically by the Automatic 
Speaker Setup function (see page 40).
RECEIVER
2
Use the Up and Down [
]/[
] 
buttons to select “3. Speaker 
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
3
Use the Up and Down [
]/[
] 
buttons to select “Speaker Con-
figuration,” and then press 
[ENTER].
The Speaker Config menu appears.
4
Use the Up and Down [
]/[
] 
buttons to select “a. Subwoofer,” 
and then use the Left and Right 
[
]/[
] buttons to select:
Yes: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
nected.
5
Use the Up and Down [
]/[
] 
buttons to select “b. Front,” and 
then use the Left and Right 
[
]/[
] buttons to select a 
crossover frequency.
Note:
• If the Subwoofer setting in step 4 is 
set to No, this is fixed at Full Band.
6
Use the Up and Down [
]/[
] 
buttons to select “c. Center,” and 
then use the Left and Right 
[
]/[
] buttons to select a 
crossover frequency.
If no center speaker is connected, select 
None.
Note:
• If the Front setting in step 5 is set to 
anything other than Full Band, Full 
Band cannot be selected here.
ENTER
ENTER
ENTER
ENTER
3-2.Speaker Config
------------------------
 a.Subwoofer      :Yes
 b.Front    :80Hz(THX)
 c.Center   :80Hz(THX)
 d.Surround :80Hz(THX)
 e.SurrBack :80Hz(THX)
 f.SurrBack Ch    :2ch
 g.LPF of LFE
            :80Hz(THX)
 h.Subwoofer Mode
        :-------------
ENTER
ENTER
ENTER