ONKYO TX-SR876 Manual Do Utilizador
129
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Mac Address
This is the AV receiver’s MAC (Media Access Control)
address. This address cannot be changed.
address. This address cannot be changed.
Control
This setting enables or disables control over the network.
Enable: Control over the network enabled.
Disable: Control over the network disabled.
■ Port
This is the network port used for control over the net-
work.
This is the network port used for control over the net-
work.
DHCP
This setting determines whether or not the AV receiver
uses DHCP to automatically configure its IP Address,
Subnet Mask, Gateway, and DNS Server settings.
uses DHCP to automatically configure its IP Address,
Subnet Mask, Gateway, and DNS Server settings.
Enable: DHCP enabled.
Disable: DHCP disabled.
If you select “Disable”, you must configure the “IP
Address”, “Subnet Mask”, “Gateway”, and “DNS
Server” settings yourself.
Address”, “Subnet Mask”, “Gateway”, and “DNS
Server” settings yourself.
IP Address
If you set the “DHCP” setting to “Disable”, you must
specify an IP address. Enter a static IP address provided
by your ISP.
The IP address must be within the following ranges.
specify an IP address. Enter a static IP address provided
by your ISP.
The IP address must be within the following ranges.
Class A: 10.0.0.0 to 10.255.255.255
Class B: 172.16.0.0 to 172.31.255.255
Class C: 192.168.0.0 to 192.168.255.255
Most routers use Class C IP addresses.
Subnet Mask
If you set the “DHCP” setting to “Disable”, you must
specify a subnet mask address.
Enter the subnet mask address provided by your ISP
(typically: 255.255.255.0).
specify a subnet mask address.
Enter the subnet mask address provided by your ISP
(typically: 255.255.255.0).
Gateway
If you set the “DHCP” setting to “Disable”, you must
specify a gateway address.
Enter the gateway address provided by your ISP.
specify a gateway address.
Enter the gateway address provided by your ISP.
DNS Server
If you set the “DHCP” setting to “Disable”, you must
specify a DNS server.
Enter the DNS server addresses provided by your ISP.
specify a DNS server.
Enter the DNS server addresses provided by your ISP.
Proxy URL
To use a Web proxy, enter its URL here.
Proxy Port
If you’re using a Web proxy, enter a proxy port number
here.
here.
3
Use the Up and Down [
q]/[w] but-
tons to select “6. Network”, and
then press [ENTER].
The “Network” screen appears.
then press [ENTER].
The “Network” screen appears.
4
Use the Up and Down [
q]/[w] but-
tons to select the settings, and
use the Left and Right [
use the Left and Right [
e]/[r]
buttons to set them.
To enter an IP address, select the set-
ting, and then press [ENTER]. The
arrow [
To enter an IP address, select the set-
ting, and then press [ENTER]. The
arrow [
q]/[w]/[e]/[r] buttons can
then be used to enter numbers. Press
[ENTER] again to set the number.
The settings are explained on the next
page.
[ENTER] again to set the number.
The settings are explained on the next
page.
5
When you’ve finished, press the
Up and Down [
Up and Down [
q]/[w] buttons to
select “
Save Settings”, and
then press [ENTER].
Setup closes.
Setup closes.
When modifying network settings,
after modifying it is necessary to exe-
cute “
after modifying it is necessary to exe-
cute “
Save Settings”.
6
When you’ve finished, press the
[SETUP] button.
Setup closes.
[SETUP] button.
Setup closes.
7-6. Network
MAC Address
Control
Control
Port
xx : xx : xx : xx : xx : xx
Enable
xxxxx
MOVE
VALUE
INPUT
RETURN
ENTER
RETURN
EXIT
SETUP
7-6. Network
Proxy
Proxy URL
Proxy Port
Save Settings
Disable
8080
MOVE
VALUE
ENTER
RETURN
ENTER
RETURN
EXIT
SETUP