ONKYO TX-SR876 Manual Do Utilizador
35
■ “Monitor Out” Setting Set to
“Analog”
With the “Monitor Out” setting set to “Analog”
(see page 52), video input signals flow through
the AV receiver as shown, with composite
video and S-Video sources being upconverted
for the component video output. Use this set-
ting if you connect the AV receiver’s COM-
PONENT VIDEO MONITOR OUT to your
TV.
(see page 52), video input signals flow through
the AV receiver as shown, with composite
video and S-Video sources being upconverted
for the component video output. Use this set-
ting if you connect the AV receiver’s COM-
PONENT VIDEO MONITOR OUT to your
TV.
Composite video is upconverted to S-Video
and S-Video is downconverted to composite
video. Note that these conversions only apply
to the MONITOR OUT V and S outputs, not
the VCR/DVR OUT V and S outputs.
and S-Video is downconverted to composite
video. Note that these conversions only apply
to the MONITOR OUT V and S outputs, not
the VCR/DVR OUT V and S outputs.
The composite video, S-Video, and component
video outputs pass through their respective
input signals as they are.
video outputs pass through their respective
input signals as they are.
This signal flow also applies when the Monitor
Out “Resolution” setting is set to “Through” (see page 55).
Out “Resolution” setting is set to “Through” (see page 55).
Video Signal Flow and the Resolution Setting
When the “Monitor Out” setting is set to “Ana-
log” (see page 52), if the Monitor Out “Reso-
lution” setting is set to anything other than
“Through” (see page 55), the video signal flow
will be as shown here, with composite video
and S-Video sources being upconverted for the
component video output.
When the “Monitor Out” setting is set to “Ana-
log” (see page 52), if the Monitor Out “Reso-
lution” setting is set to anything other than
“Through” (see page 55), the video signal flow
will be as shown here, with composite video
and S-Video sources being upconverted for the
component video output.
The composite video, S-Video, and component
video outputs pass through their respective
analog input signals as they are. HDMI input
signals are not output.
video outputs pass through their respective
analog input signals as they are. HDMI input
signals are not output.
Audio Connection Formats
Audio equipment can be connected to the AV
receiver by using any of the following audio
connection formats: analog, optical, coaxial,
analog multichannel, or HDMI.
receiver by using any of the following audio
connection formats: analog, optical, coaxial,
analog multichannel, or HDMI.
When choosing a connection format, bear in
mind that the AV receiver does not convert dig-
ital input signals for analog line outputs and
vice versa. For example, audio signals con-
nected to an optical or coaxial digital input are
not output by the analog TAPE OUT.
mind that the AV receiver does not convert dig-
ital input signals for analog line outputs and
vice versa. For example, audio signals con-
nected to an optical or coaxial digital input are
not output by the analog TAPE OUT.
IN
MONITOR OUT
DVD player, etc.
AV receiver
TV, projector, etc.
Composite
S-Video
Component
Video Signal Flow Chart
HDMI
Composite
S-Video
Component
HDMI
IN
MONITOR OUT
DVD player, etc.
AV receiver
TV, projector, etc.
Composite
S-Video
Component
Video Signal Flow Chart
HDMI
Composite
S-Video
Component
HDMI
S-Video
*
1
*
2
DVD player, etc.
AV receiver
MD recorder, etc.
Optical
Optical
Coaxial
Multichannel
Analog
Analog
Audio Signal Flow Chart
HDMI
HDMI
*1
Depends on the “Audio TV Out” setting (see page 118).
*2
Only the front L/R channels are output.