ONKYO TX-NR708 Manual Do Utilizador

En

■

PLIIz Height Gain
The Height Gain Control in Dolby Pro Logic IIz 
enables the listener to select how much gain is applied 
to the front high speakers. There are three settings, 
“Low”, “Mid” and “High”, and the front high speakers 
are accentuated in that order. While “Mid” is the default 
listening setting, the listener may adjust the Height Gain 
Control to their personal preference.

`

Low:

Low PLIIz Height Gain becomes active.

`

Mid:

Medium PLIIz Height Gain becomes active.

`

High:

High PLIIz Height Gain becomes active.

• If  the  “Front High” settings is set to “None” (

45), this setting 

cannot be selected.

■

Dolby EX
This setting determines how Dolby EX encoded signals 
are handled. This setting is unavailable if no surround 
back speakers are connected. This setting is effective 
with Dolby Digital, Dolby Digital Plus and Dolby 
TrueHD only.

`

Auto:

If the source signal contains a Dolby EX flag, the 
Dolby EX or THX Surround EX listening mode is 
used.

`

Manual:

You can select any available listening mode.

• If  the  “Surr Back” setting is set to “None” (

45), this setting 

cannot be selected.

• If  the  “Front High” or “Front Wide” setting is enabled (

45), 

this setting is fixed at “Manual”.

■

`

0 to 2 to 5

The DTS Neo:6 Music listening mode creates 6-channel 
surround sound from 2-channel stereo sources. With 
this setting, you can specify by how much the front left 
and right channel output is attenuated in order to create 
the center channel. 
Setting a value “0” in the middle is set to hear a sound. 
Sound is spread in left and right (the outside) so that the 
set value is made big. Please adjust by liking.

■

`

–3dB to Reference to +3dB

With this setting, you can adjust the soundstage when 
using Audyssey DSX™.

• If  the  “Center” setting is set to “None”, or both “Front High” 

and “Front Wide” settings are set to “None” (

45), this setting 

cannot be selected.

■

`

Wide:

Select if the listening angle is 40 degrees.

`

Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen-
sional listening mode by specifying the angle of the 
front left and right speakers relative to the listening 
position. Ideally, the front left and right speakers should 
be equidistant from the listening position and at an 
angle close to one of the two available settings.

■

`

QdB, –20dB, –10dB, or 0dB

With these settings, you can set the level of the LFE (Low 
Frequency Effects) channel individually for each input 
sources.
If you find that low-frequency effects are too loud when 
using one of these sources, change the setting to –20 dB or 
–

Q dB.

*1

Dolby Digital and Dolby Digital Plus sources.

*2

DTS and DTS-HD High Resolution Audio sources.

*3

DSD (Super Audio CD) sources.

Items can be set individually for each input selector.

When Audyssey MultEQ

®

 Room Correction and Speaker 

Setup is complete, the “Equalizer” (

47) will be set to 

“Audyssey” and the “Dynamic EQ” will be set to “On”.

■

`

:

Audyssey Dynamic EQ

®

 off.

`

On:

Audyssey Dynamic EQ on.
The Dynamic EQ indicator will light (

9).

Preparation
Press the input selector buttons to select an input source.

Front left speaker

Front right speaker