ONKYO TX-NR708 Manual Do Utilizador

En

■

■

■

■

■

■

■

■

■

■

■

■

■

When the Stereo or Mono listening mode is selected, 
only the front speakers and subwoofer produce 
sound.

—

In the Mono listening mode, only the front speakers 
output sound if the “Output Speaker” setting is set 
to “Left / Right”.

Check the Speaker Configuration.

If you use the Dolby Pro Logic IIx Movie, Dolby Pro 
Logic IIx Music, or Dolby Pro Logic IIx Game lis-
tening mode with a mono source, such as an AM 
radio station or mono TV program, the sound is con-
centrated in the center speaker.

—

In the Mono listening mode, only the front speakers 
output sound if the “Output Speaker” setting is set 
to “Center”.

Make sure the speakers are configured correctly.

When the T-D (Theater-Dimensional), Stereo or 
Mono listening mode is selected, the surround 
speakers produce no sound.

—

Depending on the source and current listening mode, 
not much sound may be produced by the surround 
speakers. Try selecting another listening mode.

—

Make sure the speakers are configured correctly.

When the Stereo or Mono listening mode is selected, 
the center speaker produces no sound.

—

In the Mono listening mode, only the front speakers 
output sound if the “Output Speaker” setting is set 
to “Left / Right”.

Make sure the speakers are configured correctly.

Depending on the current listening mode, no sound 
may be produced by the front high, front wide and 
surround back speakers. Select another listening 
mode.

Not much sound may be produced by the front high, 
front wide and surround back speakers with some 
sources.

—

Make sure the speakers are configured correctly.

While Powered Zone 2 is being used, playback in the 
main room is reduced to 5.1-channels and the front 
high, front wide and surround back speakers produce 
no sound.

When you play source material that contains no 
information in the LFE channel, the subwoofer pro-
duces no sound.

—

Make sure the speakers are configured correctly.

Check the digital audio output setting on the con-
nected device. On some game consoles, such as 
those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an 
audio output format from a menu.

—

Depending on the input signal, some listening modes 
cannot be selected.

37–41

The Pure Audio listening mode cannot be selected 
while Zone 2 is on.

—

If no surround back speakers, front wide and front 
high speakers are connected, or the Zone 2 speakers 
are being used, 6.1/7.1 playback is not possible.

—

You can not always select all of the listening modes, 
depending on the number of the speakers connected.

37–41

Check to see if a maximum volume has been set.

If the volume level of each individual speaker has 
been adjusted to high positive values, then the maxi-
mum master volume possible may be reduced. Note 
that the individual speaker volume levels are set 
automatically after Audyssey MultEQ

®

 Room Cor-

rection and Speaker Setup function has been com-
pleted.

29, 46

Using cable ties to bundle audio cables with power 
cords, speaker cables, and so on may degrade the 
audio performance, so don’t do it.

—

An audio cable may be picking up interference. Try 
repositioning your cables.

—

Make sure the source material is Dolby Digital, 
Dolby Digital Plus, and Dolby TrueHD.

When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is 
to prevent noise when you use the pause, fast for-
ward, or fast reverse function on your player. If you 
switch your player from DTS to PCM, because the 
AV receiver does not switch formats immediately, 
you may not hear any sound, in which case you 
should stop your player for about three seconds, and 
then resume playback.

—

With some CD and LD players, you won’t be able to 
playback DTS material properly even though your 
player is connected to a digital input on the AV 
receiver. This is usually because the DTS bitstream 
has been processed (e.g., output level, sampling rate, 
or frequency response changed) and the AV receiver 
doesn’t recognize it as a genuine DTS signal. In such 
cases, you may hear noise.

—