ONKYO TX-NR5007 Manual Do Utilizador
57
If you connect a component to the AV receiver’s analog
multichannel input, you must assign that input to an
input selector. For example, if you connect your DVD/
BD player to the MULTI CH input, you must assign it to
the DVD/BD input selector.
multichannel input, you must assign that input to an
input selector. For example, if you connect your DVD/
BD player to the MULTI CH input, you must assign it to
the DVD/BD input selector.
Notes:
• To listen to the component connected to the multi-
• To listen to the component connected to the multi-
channel input, press the [AUDIO] button and select
the “Audio selector” (see page 119).
the “Audio selector” (see page 119).
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
and [ENTER] button.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
To use bi-amping or bridging, you must change the
“Speakers Type(FrontA)” or “Speakers Type(FrontB)”
setting. For hookup information, see pages 23 to 26.
less than 6, set the minimum speaker impedance to 4
ohms.
To use bi-amping or bridging, you must change the
“Speakers Type(FrontA)” or “Speakers Type(FrontB)”
setting. For hookup information, see pages 23 to 26.
Notes:
• When bridging is used, the AV receiver is able to drive
• When bridging is used, the AV receiver is able to drive
up to 7.2 speakers in the main room.
• When bi-amping is used, the AV receiver is able to
drive up to 7.2 speakers in the main room.
• Before you change these settings, turn down the
volume.
Analog Audio Input Setup
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w] but-
tons to select “1. Input/Output
Assign”, and then press
[ENTER].
The “Input/Output Assign” menu
appears.
Assign”, and then press
[ENTER].
The “Input/Output Assign” menu
appears.
3
Use the Up and Down [
q]/[w] but-
tons to select “5. Analog Audio
Input”, and then press [ENTER].
The “Analog Audio Input” menu
appears.
Input”, and then press [ENTER].
The “Analog Audio Input” menu
appears.
4
Use the Left and Right [
e]/[r]
buttons to select an input selec-
tor.
You can assign the multichannel input
to the following input selectors: “DVD/
BD”, “VCR/DVR”, “CBL/SAT”,
“GAME”, “AUX 1”, “AUX 2”, “TV/
TAPE”, “CD”, or “PHONO”. If you
don’t want to assign the multichannel
input, set to “- - - - -”.
tor.
You can assign the multichannel input
to the following input selectors: “DVD/
BD”, “VCR/DVR”, “CBL/SAT”,
“GAME”, “AUX 1”, “AUX 2”, “TV/
TAPE”, “CD”, or “PHONO”. If you
don’t want to assign the multichannel
input, set to “- - - - -”.
1. Input/Output
Assign
1. Monitor
Out
2. HDMI
Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
4. Digital Audio Input
5. Analog Audio Input
Multich
Subwoofer Input Sensitivity
Subwoofer Input Sensitivity
- - - - -
1–5. Analog Audio Input
5
Press the [SETUP] button.
The setup menu closes.
The setup menu closes.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
If you change these settings, you must run
Audyssey MultEQ
Audyssey MultEQ
®
XT Room Correction and
Speaker Setup again (see page 61).