ONKYO TX-NR5007 Manual Do Utilizador
95
Some of the settings in this section are set automatically by Audyssey MultEQ
®
XT Room Correction and Speaker
Setup (see page 61). For Speakers B, you need to change the settings manually.
Here you can check the settings made by Audyssey MultEQ
Here you can check the settings made by Audyssey MultEQ
®
XT Room Correction and Speaker Setup, or set them
manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ
®
XT Room Cor-
rection and Speaker Setup.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Speaker Setup
1
Press the [RECEIVER] button, and then
use the remote controller’s [SP LAYOUT]
button to select Speakers A or
Speakers B.
use the remote controller’s [SP LAYOUT]
button to select Speakers A or
Speakers B.
Note:
Speakers B cannot be selected if “Speakers
Type(FrontB)” is set to “Not Use”.
Speakers B cannot be selected if “Speakers
Type(FrontB)” is set to “Not Use”.
2
Press the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
3
Use the Up and Down [
q]/[w] buttons to
select “2. Speaker Setup”, and then press
[ENTER].
[ENTER].
4
Use the Up and Down [
q]/[w] buttons to
select the submenu, and then press
[ENTER].
[ENTER].
5
Use the Up and Down [
q]/[w] buttons to
select setting, and then use the Left and
Right [
Right [
e]/[r] buttons to set them.
6
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
button.
The setup menu closes.
Speaker Settings
See “Speaker Settings” on page 57.
See “Speaker Settings” on page 57.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. You
can set the crossover frequencies, distances, and levels of the front Speakers A and front Speakers B independently.
The other speakers (i.e., subwoofer, center, surround, and surround back) use the same crossover frequencies, dis-
tances, and levels for Speakers A and Speakers B. The following crossover frequencies can be specified: “Full Band”,
“40Hz”, “50Hz”, “60Hz”, “70Hz”, “80Hz(THX)”, “90Hz”, “100Hz”, “120Hz”, “150Hz”, or “200Hz”. Specify “Full
Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized
woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by
the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequen-
cies.
If you set up your speakers using Audyssey MultEQ
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. You
can set the crossover frequencies, distances, and levels of the front Speakers A and front Speakers B independently.
The other speakers (i.e., subwoofer, center, surround, and surround back) use the same crossover frequencies, dis-
tances, and levels for Speakers A and Speakers B. The following crossover frequencies can be specified: “Full Band”,
“40Hz”, “50Hz”, “60Hz”, “70Hz”, “80Hz(THX)”, “90Hz”, “100Hz”, “120Hz”, “150Hz”, or “200Hz”. Specify “Full
Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized
woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by
the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequen-
cies.
If you set up your speakers using Audyssey MultEQ
®
XT Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
1ch: Audio signal is outputted from SW1 jack only.
2ch: Audio signal is outputted from SW1 and SW2 jacks (default).
2ch: Audio signal is outputted from SW1 and SW2 jacks (default).
No: Select if no subwoofer is connected.
Front
*1
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX) (default), 90Hz, 100Hz, 120Hz,
150Hz, 200Hz
150Hz, 200Hz
Center
*2
Surround
*2
Front Wide
*2*3*5*7
Front High
*2*3*7*10
Surr Back
*3*4*6
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 120Hz, 150Hz,
200Hz
200Hz
None: Select if no speaker is connected.