ONKYO TX-SR875 Manual Do Utilizador
111
Controlling Other Components
—Continued
The AV receiver’s remote controller can learn the com-
mands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s
remote controller, the remote controller can learn it, and
then transmit the exact same command when its Play
[
mands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s
remote controller, the remote controller can learn it, and
then transmit the exact same command when its Play
[
] button is pressed in the CD remote mode.
This is useful when you’ve entered the appropriate
remote control code (page 108) but some buttons don’t
work as expected.
remote control code (page 108) but some buttons don’t
work as expected.
Notes:
• The following buttons cannot learn new commands:
REMOTE MODE, MACRO [1], [2], [3], TV [
],
TV [INPUT], TV CH [+]/[–], TV VOL [
]/[
],
Light.
• The remote controller can learn approximately 70 to
90 commands, although this will be less if commands
that use a lot of memory are learned.
that use a lot of memory are learned.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Onkyo CD players, cassette decks, and
DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands at any time by resetting the remote controller
(see page 109).
controlling Onkyo CD players, cassette decks, and
DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands at any time by resetting the remote controller
(see page 109).
• To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
learned all over again, so don’t discard your other
remote controllers.
Learning Commands
1
While holding down the REMOTE
MODE button for the mode in
which you want to use the com-
mand, press the [ON] button.
MODE button for the mode in
which you want to use the com-
mand, press the [ON] button.
The Remote indicator lights up.
2
Press the button you want to
learn the new command.
learn the new command.
INPUT SELECTOR
ON
STANDBY
DISPLAY
MUTING
GU
IDE
EXI
T
PREV
CH
DIMMER
CDR/MD
SAT
TAPE/AMP
SLEEP
MACRO
REMOTE MODE
--/--- 10
11
12
TV
TV CH
TV VOL
DVD
AUX
1
AUX
2
GAME/TV
CBL/SAT
VCR/DVR
D. TUN
CD
TUNER
TAPE
PHONO
ENTER
TO
P M
ENU
MEN
U
VOL
CH
DISC
ALBUM
TV
VCR
CABLE
DOCK
DVD
RECEIVER
CD
+
-
1
2
3
ZONE
3
ZONE
2
INPUT
+
-
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
SE
TUP
RET
UR
N
1, 4
1
Remote
indicator
indicator
CDR/MD
SAT
TAPE/AMP
REMOTE MODE
TV
VCR
CABLE
DOCK
DVD
RECEIVER
CD
ON
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
If the command is learned successfully,
the Remote indicator flashes twice.
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
steps 2 and 3.
Press any REMOTE MODE button
when you’ve finished.
when you’ve finished.
POWER
SLEEP
DIMM
ER
SUR
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TU
NER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUME
EVEL
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
GROUP
R
10
--/-
--
11
12
R
EM
O
TE M
O
DE
ZO
NE
2
DVD
VCR
CD
ZO
NE
3
RECEIVER
CABLE
DOCK
TAPE/A
MP
SAT
CDR/MD
+
-
T V
C
H
T V
V
O
L
SLEEP
INPUT SELECTOR
3
2
MACRO
1
+10
0
CLEAR
D.TUN
1
2
3
4
5
6
7
8
9
IN
PU
T
I
O
N
ST
AN
D
BY
T V
TA
PE
D
V
D
DC
R/D
VR
CB
L/S
AT
AUX1
AU
X2
TU
N
ER
CD
PHONO
GA
M
E/T
V
About 2 to 6
inches (5–15 cm)
inches (5–15 cm)
RC-690M
TX-SR805_875_En.book Page 111 Thursday, April 26, 2007 3:00 PM