ONKYO HT-R518 Manual Do Utilizador

 

75

 

• Make sure that the batteries are installed with the cor-

rect polarity (page 12).

• Make sure that the remote controller is not too far 

away from the AV receiver and there’s no obstruction 
between the remote controller and the AV receiver’s 
remote control sensor (page 12).

• Make sure you’ve selected the correct remote control-

ler mode.

• Make sure you’ve entered the correct remote control 

code (page 64).

 

• Make sure you’ve selected the correct remote control-

ler mode.

• If you’ve connected an 

-capable Onkyo MD 

recorder, CD recorder, or RI Dock to the TAPE 
IN/OUT jacks, or an RI Dock to the CBL/SAT IN 
jacks, for the remote controller to work properly, you 
must set the Input Display to MD, CDR, or DOCK, 
respectively (see page 38).

• The entered remote control code may not be correct. If 

more than one code is listed, try each one.

• With some AV components, certain buttons may not 

work as expected, and some may not work at all.

• To control an Onkyo component that’s connected via 

, point the remote controller at the AV receiver. Be 

sure to enter the appropriate remote control code first 
(page 65).

• To control an Onkyo component that’s not connected 

via 

, or another manufacturer’s component, point 

the remote controller at that component. Be sure to 
enter the appropriate remote control code first 
(page 64).

 

• On your recorder, make sure the correct input is 

selected.

• To prevent signal loops and damage to the AV 

receiver, input signals are not fed through to outputs 
with the same name (e.g., TAPE IN to TAPE OUT or 
VCR/DVR IN to VCR/DVR OUT).

• When the Pure Audio listening mode is selected, video 

recording is not possible because no video signals are 
output. Select another listening mode.

 

• When a pair of headphones is connected, the listening 

mode is set to Stereo, unless it’s already set to Stereo, 
Mono, Direct, or Pure Audio, in which case it stays the 
same.

 

• On the “Audio Adjust” menu, change the “Input 

(Mux)” setting to Main or Sub (page 55).

 

• To use 

, you must make an 

 connection and an 

analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 32).

 

• The display is turned off when the Pure Audio listen-

ing mode is selected. Select another listening mode.

 

You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the 

input source that you want to set, press the [SETUP] 
button.

2. Use the Left and Right [

]/[

] buttons to change 

the setting.

3. Press the [SETUP] button when you’ve finished.

 

This setting can be made for the DVD, VCR/DVR, 
CBL/SAT, or AUX input.
If you have a games console connected to the 
S-Video or composite video input, and the picture 
isn’t very clear, you can attenuate the gain.

 

 (default).

 

 Gain is reduced by 2 dB.

 

The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations, 
severe interference, noise from an external source, or 
static electricity may cause it to lockup. In the unlikely event 
that this happens, unplug the power cord from the wall out-
let, wait at least 5 seconds, and then plug it back in again.

Onkyo is not responsible for damages (such as CD 
rental fees) due to unsuccessful recordings caused by 
this unit’s malfunction. Before you record important 
data, make sure that the material will be recorded cor-
rectly.

Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.

HT-R518_En.book Page 75 Tuesday, March 11, 2008 11:31 AM