ONKYO 29400021 Manual Do Utilizador
85
Some of the settings in this section are set automatically by Audyssey MultEQ
®
Room Correction and Speaker Setup
(see page 54).
Here you can check the settings made by Audyssey MultEQ
Here you can check the settings made by Audyssey MultEQ
®
Room Correction and Speaker Setup, or set them manu-
ally, which is useful if you change one of the connected speakers after using Audyssey MultEQ
®
Room Correction and
Speaker Setup.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Speaker Setup
1
Press the [RECEIVER] button followed by
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [
q]/[w] buttons to
select main menu, and then press
[ENTER].
[ENTER].
3
Use the Up and Down [
q]/[w] buttons to
select the submenu, and then press
[ENTER].
[ENTER].
4
Use the Up and Down [
q]/[w] buttons to
select setting, and then use the Left and
Right [
Right [
e]/[r] buttons to set them.
5
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
button.
The setup menu closes.
Speaker Settings
See “Speaker Settings” on page 51.
See “Speaker Settings” on page 51.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. The
following crossover frequencies can be specified: “Full Band”, “40Hz”, “50Hz”, “60Hz”, “70Hz”, “80Hz(THX)”,
“90Hz”, “100Hz”, “120Hz”, “150Hz”, or “200Hz”. Specify “Full Band” for speakers that can output low frequency
bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover
frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum crossover frequencies.
If you set up your speakers using Audyssey MultEQ
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. The
following crossover frequencies can be specified: “Full Band”, “40Hz”, “50Hz”, “60Hz”, “70Hz”, “80Hz(THX)”,
“90Hz”, “100Hz”, “120Hz”, “150Hz”, or “200Hz”. Specify “Full Band” for speakers that can output low frequency
bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover
frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum crossover frequencies.
If you set up your speakers using Audyssey MultEQ
®
Room Correction and Speaker Setup, please make sure manu-
ally that any THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
Yes: Select if a subwoofer is connected (default).
No: Select if no subwoofer is connected.
Front
*1
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX) (default), 90Hz, 100Hz, 120Hz,
150Hz, 200Hz
150Hz, 200Hz
Center
*2
Surround
*2*6
Front Wide
*2*3*5*6
Front High
*2*3*5*6
Surr Back
*3*4*5*6
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 120Hz, 150Hz,
200Hz
200Hz
None: Select if no speaker is connected.
Surr Back Ch
*7
1ch: Select if only one surround back L speaker is connected.
2ch: Select if two (left and right) surround back speakers are connected (default).
2ch: Select if two (left and right) surround back speakers are connected (default).
TX-NR807_En.book Page 85 Tuesday, July 28, 2009 12:00 PM