ONKYO HT-R980 Manual Do Utilizador

En

■

`

Off: 

Select “Off” if you don’t want to use audio return 
channel (ARC) function.

`

Auto:

The audio signal from your TV tuner can be sent to 
the HDMI OUT of the AV receiver.

Audio return channel (ARC) function enables an HDMI 
(Audio Return Channel) capable TV to send the audio 
stream to the HDMI OUT of the AV receiver. To use this 
function, you must select the TV/CD input selector and 
your TV must support ARC function.

• The  “Audio Return Channel” setting can be set only when the 

“HDMI Control (RIHD)” setting is set to “On”.

• This setting is set to “Auto” automatically when the “HDMI 

Control (RIHD)” is set to “On” first time.

■

`

Off: 

Power Control disabled.

`

On:

Power Control enabled.

To link the power functions of 

p-compatible com-

ponents connected via HDMI, select “On”.
This setting is set to “On” automatically when the 
“HDMI Control (RIHD)” is set to “On” first time.

• The 

“Power Control”

 setting can be set only when the 

“

”

 setting is set to “On”.

• HDMI power control only works with 

p-compatible 

components that support it and may not work properly with 
some components due to their settings or compatibility.

• When set to “On”, power consumption will increase.
• When set to “On”, regardless of whether the AV receiver is On 

or in Standby, both audio and video stream from an HDMI input 
will be output to the TV or other components via HDMI connec-
tion (HDMI pass through function). When the HDMI pass 
through function activates in standby mode, HDMI THRU indi-
cator will light.

• The power consumption during standby mode will increase dur-

ing the HDMI pass through function; however in the following 
cases, the power consumption can be saved:
1. The TV is in standby mode.
2. You are watching a TV program.

• Refer to the connected component’s instruction manual for 

details.

■

`

Off: 

TV Control disabled.

`

On:

TV Control enabled.

Set to “On” when you want to control the AV receiver 
from an 

p-compatible TV that is connected to 

HDMI.

• Do not assign the component connected with the HDMI input to 

the TV/CD selector when you set “TV Control” setting to “On”. 
Otherwise, appropriate CEC (Consumer Electronics Control) 
operation is not guaranteed.

• Set  to 

“

”

 when the TV is not compatible or when it is unclear 

whether the TV is compatible or not.

• The 

“TV Control”

 setting can be set only when the 

“

”

 (

49) and 

“Power Control”

 settings are 

both set to “On”.

• Refer to the connected component’s instruction manual for 

details.

With this preference, you can protect your settings by 
locking the setup menus.

■

`

Locked:

Setup menus locked.

`

Unlocked:

Setup menus not locked.

When the setup menus are locked, you cannot change any 
setting.

You can change various audio settings from the Audio 
menu (

22).

These settings are disabled when:

• a pair of headphones is connected, or 
• the  “Audio TV Out” setting is set to “On” (

49) and an input 

selector other than HDMI is selected.

You can adjust the bass and treble for the front speakers, 
except when the Direct or THX listening mode is selected.

■

`

–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut low-frequency sounds output 
by the front speakers.

■

`

–10dB to 0dB to +10dB in 2 dB steps.

You can boost or cut high-frequency sounds output 
by the front speakers.

After changing the settings of the “HDMI Control 
(RIHD)”, “Audio Return Channel”, “Power Con-
trol”, or “TV Control”, turn off the power to all con-
nected pieces of equipment and then turn them on again. 
Refer to the user’s manuals for all connected pieces of 
equipment.

q/w/e/r to make the desired selection.