Pioneer VSX-322-K Manual Do Utilizador

En

No picture or sound.
 If the problem still persists when connecting your HDMI 

component directly to your monitor, please consult the 

component or monitor manual or contact the manufacturer 

for support.

No picture.
 Video signals that are input from the analog video terminal 

will not output from the HDMI terminal. Signals that are input 

from the HDMI terminal will not output from the analog video 

terminal. Be consistent with the type of cable between input 

and output.

 Depending in the output settings of the source component, it 

may be outputting a video format that can’t be displayed. 

Change the output settings of the source, or connect using 

the composite jacks.

 This receiver is HDCP-compatible. Check that the components 

you are connecting are also HDCP-compatible. If they are not, 

please connect them using the composite video jacks.

 Depending on the connected source component, it’s possible 

that it will not work with this receiver (even if it is HDCP-

compatible). In this case, connect using the composite video 

jacks between source and receiver.

 If video images do not appear on your TV, try adjusting the 

resolution, Deep Color or other setting for your component.

 To output signals in Deep Color, use an HDMI cable (High 

Speed HDMI

®

 Cable) to connect this receiver to a component 

or TV with the Deep Color feature.

No sound, or sound suddenly ceases.
 Check that the Audio Parameter setting is set to HDMI AMP/

 (refer to page 23).

 If the component is a DVI device, use a separate connection 

for the audio.

 HDMI format digital audio transmissions require a longer time 

to be recognized. Due to this, interruption in the audio may 

occur when switching between audio formats or beginning 

playback.

 Turning on/off the device connected to this unit’s HDMI OUT 

terminal during playback, or disconnecting/connecting the 

HDMI cable during playback, may cause noise or interrupted 

audio.

There are cases where you may not be able to route HDMI 

signals through this receiver (this depends on the HDMI 

equipped component you are connecting-check with the 

manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this 

receiver (from your component), please try the following 

configuration when connecting up.

Connect your HDMI-equipped component directly to the 

display using an HDMI cable. Then use the most convenient 

connection (digital is recommended) for sending audio to the 

receiver. See the operating instructions for more on audio 

connections. Set the display volume to minimum when using 

this configuration.

• Depending on the component, audio output may be 

limited to the number of channels available from the 

connected display unit (for example audio output is 

reduced to 2 channels for a monitor with stereo audio 

limitations).

• If you want to switch the input source, you’ll have to 

switch functions on both the receiver and your display 

unit.

• Since the sound is muted on the display when using the 

HDMI connection, you must adjust the volume on the 

display every time you switch input sources.

Use this procedure to reset all the receiver’s settings to the 

factory default. Use the front panel controls to do this.

 STANDBY/ON for about two seconds.

 shows in the display.

 appears in the display to indicate that the receiver has 

been reset to the factory default settings.

• If the ARC function is ON, you may not be able to initialize 

the unit. If this happens, turn OFF the ARC function or 

turn OFF all the connected device before turning OFF 

(STANDBY) the power for this unit, and initialize after the 

HDMI indicator goes out.

• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• When the surface is dirty, wipe with a soft cloth dipped in 

some neutral cleanser diluted five or six times with water, 

and wrung out well, and then wipe again with a dry cloth. 

Do not use furniture wax or cleansers.

• Never use thinners, benzine, insecticide sprays or other 

chemicals on or near this unit, since these will corrode 

the surface.