Pioneer VSX-919AH-K Manual Do Utilizador
Basic Setup
04
38
En
Select
Normal (Surround back), Speaker B,
Front Bi-Amp or ZONE 2 for the Surr Back
System setting according to connections to
the surround back speaker terminals.
System setting according to connections to
the surround back speaker terminals.
4
Follow the instructions on-screen.
Make sure the microphone is connected, and if
you’re using a subwoofer, make sure it is switched
on and set to a comfortable volume level.
you’re using a subwoofer, make sure it is switched
on and set to a comfortable volume level.
5
Wait for the test tones to finish, then
confirm the speaker configuration in the GUI
screen.
A progress report is displayed on-screen while
the receiver outputs test tones to determine the
speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
screen.
A progress report is displayed on-screen while
the receiver outputs test tones to determine the
speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
1
If no operations are performed for 10 seconds
while the speaker configuration check screen
is being displayed, the Auto MCACC Setup will
resume automatically. In this case, you don’t
need to select ‘
while the speaker configuration check screen
is being displayed, the Auto MCACC Setup will
resume automatically. In this case, you don’t
need to select ‘
OK’ and press ENTER in step 6.
• With error messages (such as
Too much
ambient noise! or Check microphone.)
select
select
RETRY after checking for ambient
noise (see
MCACC Setup below) and verifying the mic
connection. If there doesn’t seem to be a
problem, you can simply select
connection. If there doesn’t seem to be a
problem, you can simply select
GO NEXT
and continue.
The configuration shown on-screen should
reflect the actual speakers you have.
reflect the actual speakers you have.
• If you see an
ERR message (or the speaker
configuration displayed isn’t correct), there
may be a problem with the speaker
connection.
If selecting
may be a problem with the speaker
connection.
If selecting
RETRY doesn’t work, turn off
the power and check the speaker
connections. If there doesn’t seem to be a
problem, you can simply use
connections. If there doesn’t seem to be a
problem, you can simply use
/ to select
the speaker and
/ to change the
setting and continue.
• If
Reverse Phase is displayed, the
speaker’s wiring (+ and –) may be inverted.
Check the speaker connections.
Check the speaker connections.
2
If the connections were wrong, turn off the
power, disconnect the power cable, then
reconnect properly. After this, perform the
Full Auto MCACC procedure again.
power, disconnect the power cable, then
reconnect properly. After this, perform the
Full Auto MCACC procedure again.
6
Make sure ‘OK’ is selected, then press
ENTER.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
Channel Level, Speaker Distance, Standing
Wave and Acoustic Cal EQ.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
Channel Level, Speaker Distance, Standing
Wave and Acoustic Cal EQ.
Again, try to be as quiet as possible while this
is happening. It may take 3 to 10 minutes.
is happening. It may take 3 to 10 minutes.
Note
1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
Now Analyzing...
2/10
Environment Check
1a.Full Auto MCACC
A/V RECEIVER
Exit
Cancel
Ambient Noise
: OK
Microphone :
Speaker YES/NO
Speaker YES/NO
:
L : YES
R : YES
C : YES
1a.Full Auto MCACC
SR : YES
SBR :
SBR :
YES
SBL :
YES
SL : YES
SW :
SW :
YES
10
OK
RETRY
A/V RECEIVER
Exit
Cancel
2 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase
(dipole speakers, reflective speakers, etc.),
Reverse Phase may be displayed even if the speakers are properly
connected. If this happens, select
GO NEXT and continue.
VSX-1019_KU.book Page 38 Thursday, January 8, 2009 12:01 PM