Wharfedale 10.2 Manual Do Utilizador

Introduction

Preparing the Subwoofer

Positioning the Subwoofer

Wharfedale subwoofers are intended for use with high quality domestic sound systems. They are equally effective in

Stereo and Home Cinema applications. Your subwoofer will  probably be used in conjunction with Wharfedale

loudspeakers though they will partner any audiophile or top-quality home cinema amplification and loudspeakers.

No further preparation is necessary.

You should attach the spikes or protective rubber feet to the subwoofer.

Carefully invert the subwoofer. Protect the top by placing it

on a soft surface such as a towel. Open the protective bag

and slide it part-way down the cabinet. Two sets of

adjustable screw feet are provided - regular and spiked.

Choose one set only - do not use a mixture of spiked and

regular feet.

Screw the threaded washer over each foot as shown. Screw

a foot part-way into the threaded hole at the bottom of

each leg of the subwoofer and hand-tighten the washer.

When all four screw feet have been fitted, stand the subwoofer upright and remove the bag.

With the aid of a spirit level, screw each foot in and out until the subwoofer is

level (side to side and front to back) and firmly supported on all four feet. Tighten

the washer with a wrench to lock the assembly in position.

Note: When using spiked feet take care not to drag the subwoofer and be careful

not to pierce objects or cables which may be hidden under carpets, etc. Spikes

are not suitable for use with stone floors and can cause damage to wood floors,

so consider carefully before deciding which feet to use.

Although the unit may be placed almost anywhere in the room, we recommend that it be placed in front of the

listener and as central to the listening position as possible. There should be a mains outlet within easy reach. The

subwoofer should not be operated within 450mm of a television set as the drive unit magnet may distort the picture.

The bass unit is mounted underneath the subwoofer and moves a lot of air at high volume, so make sure the floor is

sound. Do not place the subwoofer with the bass port near surfaces or objects that may rattle.

We suggest you initially position the subwoofer about 20cm (8 inches) from the wall. Placing the unit close to the

wall will enhance the bass; placing it across the corner of the room will increase the bass further, possibly at the

expense of clarity.

Experiment with locations and sources before making a final decision.

Unpacking your Subwoofer

Before Connecting the Subwoofer

Open the carton and remove all the top packing pieces. Lift the subwoofer out taking care not to damage the

cabinet. When lifting the unit from the carton support it from the bottom. DO NOT attempt to lift the subwoofer out

of the carton using the protective bag. The unit is heavy; if you cannot manage it easily, get someone to assist you.

Switch off your amplifier and all connected source units at the mains. Unplug the power cords if necessary.

Make sure the subwoofer is disconnected from the mains and that the ON/OFF switch is OFF.

Before re-connecting your system  to the AC power supply, check that all the connections are properly made.

Signal cables should be properly terminated and fully screened to minimise hum. If you connect your subwoofer

via the low level signal inputs, the cable between your control unit or processor and the subwoofer could be

quite long so screening is particularly  important. Consult your dealer if in doubt

#
#
#
#

Diamond 10 Subwoofers

Screw

Foot

Threaded

Washer

10

AC 220-240V~50Hz 400W

FUSE T4AL250V

AC 220-240V~50Hz 400W

FUSE T4AL250V

POWER

LEFT

LEFT

INPUT

OUTPUT

RIGHT

RIGHT

CROSSOVER
FREQUENCY

CROSSOVER
FREQUENCY

VOLUME

0

35Hz

85Hz

45Hz

75Hz

55Hz

65Hz

10

OFF

ON

SERIAL No:

PHASE

180°

0°

Connecting Your Subwoofer - 1

b

c

d

e

f

g

h

i

j

Subwoofer Volume Control

Crossover Frequency Control

Phase Control

Mains Power Switch

IEC Mains Input Socket

Mains Power Fuse

Speaker Level Inputs

Line Level Inputs

Line Level Outputs

b

c

d

f

g

h

i

j

Subwoofer Volume Control

Auto Power Switch

I

Phase Switch

Crossover Frequency Control

Mains Power Switch

EC Mains Input Socket

Mains Power Fuse

Speaker Level Inputs

Line Level Inputs

Line Level Outputs

USB  Power Supply Port*

e

1)

1!

DIAMOND 10. GX-SUB REAR PANEL

DIAMOND 10. MX-SUB  REAR PANEL

35

45

55

65

75

85

(Hz)

N  21090

DIAMOND 10. SX-SUB  REAR PANEL

All three subwoofers feature the same connectivity.

- a USB power supply

receiver. This receiver enables a Subwoofer to receive signals from a suitably equipped AV

amplifier or processor without the need for a signal input interconnect.  Consult your Wharfedale dealer for details.

1! for charging the internal battery of an

optional wireless

11