QSC Audio DSP 322UA Manual Do Utilizador
14
Getting Started
This section outlines one of the simpler methods of getting familiar with your DSP 322ua and the QSControl.net software. The goal of
this procedure is to get your computer and the DSP 322ua connected and communicating and the QSControl.net software installed and
running. After the software is installed and running, refer to the software’s Help file for all software related operation/issues. Note!
The default password for the DSP 322ua is “qsc” (no quotes, lower case).
this procedure is to get your computer and the DSP 322ua connected and communicating and the QSControl.net software installed and
running. After the software is installed and running, refer to the software’s Help file for all software related operation/issues. Note!
The default password for the DSP 322ua is “qsc” (no quotes, lower case).
1- Turn off the computer and unplug the power cord from the DSP 322ua.
2- Connect a CAT-5 crossover cable from the computer’s network interface card (NIC) to the DSP 322ua QSControl jack (example 1, page
5).
5).
3- Reconnect the power cord to the DSP 322ua (turn it on). Using the DSP 322ua LCD display and controls, navigate the menu to the IP
Address and make a note of it. In steps 12 and on, you will need to change the IP address of the DSP 322ua or your PC.
Address and make a note of it. In steps 12 and on, you will need to change the IP address of the DSP 322ua or your PC.
4- Turn on the PC and start Windows. You must have Administrator rights and be signed on as Administrator in order to install the
QSControl.net program. Ensure you are signed on to the computer as the Administrator.
QSControl.net program. Ensure you are signed on to the computer as the Administrator.
5- Place the QSControl.net CD-ROM in your CD-ROM drive. The install wizard should start. If not, you can also select Start then Run
and browse for the file named setup.exe from the CD.
and browse for the file named setup.exe from the CD.
6- The installer queries the computer for available drive space and other information. If required MDAC library (Microsoft) files are not
already on the computer, the library files are installed. You must accept the Microsoft software agreement in order to install the MDAC
library. It may be necessary to reboot the computer after library installation.
already on the computer, the library files are installed. You must accept the Microsoft software agreement in order to install the MDAC
library. It may be necessary to reboot the computer after library installation.
7- At the prompt for “Client/Server” selection, keep both Client and Server selected. This will be appropriate for general use.
8- When prompted “Select Installation Folder”, specify the installation directory or accept the default location.
9- You will be prompted to select an installation accessible by everyone (non-secure) or an installation accessible only to you (secure).
Select the appropriate Everyone or Just Me box and continue. Installation proceeds.
Select the appropriate Everyone or Just Me box and continue. Installation proceeds.
10- Reboot only if your computer prompts you to do so.
11- Select Network Connections in the control panel. Select Properties. Right-click Local Area Connection, and view its proper-
ties. Highlight the Internet Protocol (TCP/IP) tab and view its properties. You will see an entry field for the IP address. Decide
whether you want to change the IP address of your computer to be similar that of to the DSP 322ua (easiest if you have many DSP
322ua units) or if you want to change the IP address of your DSP 322ua to be similar to that of the computer. This is a network manage-
ment decision.
ties. Highlight the Internet Protocol (TCP/IP) tab and view its properties. You will see an entry field for the IP address. Decide
whether you want to change the IP address of your computer to be similar that of to the DSP 322ua (easiest if you have many DSP
322ua units) or if you want to change the IP address of your DSP 322ua to be similar to that of the computer. This is a network manage-
ment decision.
12- Change the IP address of the DSP 322ua (or computer) to be compatible with that of the computer (or DSP 322ua). Typically, this is
done by making the IP address of one of the devices 1 digit different in the last octet (group of digits in IP address). If changing the com-
puter’s settings, write down the current values, in case you want to revert later.
done by making the IP address of one of the devices 1 digit different in the last octet (group of digits in IP address). If changing the com-
puter’s settings, write down the current values, in case you want to revert later.
13- The subnet mask address should be exactly the same for both the computer and the DSP 322ua. The Gateway address should not
be altered as it is not used.
be altered as it is not used.
14- After you are satisfied with all your settings, close all open windows and start the QSControl.net program. Select Start, All Pro-
grams, QSControl.net, Venue Manager.
grams, QSControl.net, Venue Manager.
15- The login screen should open. The default password is “qsc” (lower case, no quotation marks). Select “Log on to Local Computer”
and click OK.
and click OK.
16-The QSControl.net Venue Manager window will open. A Startup Tips screen will be visible the first time Venue Manager is
launched. Optionally, the Startup Tips screen may be disabled by un-checking the box in it’s lower left corner. It is highly recom-
mended the user become familiar with each of the tips listed on this screen. After reviewing the tip(s), close the Startup Tips screen.
launched. Optionally, the Startup Tips screen may be disabled by un-checking the box in it’s lower left corner. It is highly recom-
mended the user become familiar with each of the tips listed on this screen. After reviewing the tip(s), close the Startup Tips screen.