ONKYO TX-NR1000 Manual Do Utilizador
11
Index Parts and Facilities
—Continued
For further operational instructions, see the pages
indicated in brackets [ ].
indicated in brackets [ ].
1
POWER switch (for all models other than
USA, Canadian, and Australian models) [50]
USA, Canadian, and Australian models) [50]
Press to turn on and off the main power supply for
the TX-NR1000/TX-NR5000E. When the
TX-NR1000/TX-NR5000E is turned on with the
[POWER] switch, the [STANDBY] indicator lights.
• Before turning on the power, check to make sure
the TX-NR1000/TX-NR5000E. When the
TX-NR1000/TX-NR5000E is turned on with the
[POWER] switch, the [STANDBY] indicator lights.
• Before turning on the power, check to make sure
that all cords are properly connected.
• When the power is turned on, a sudden surge of
current will occur that may adversely affect the
operation of other devices. To prevent this, do not
plug the TX-NR1000/TX-NR5000E into the same
circuit used by sensitive equipment, e.g., computers.
operation of other devices. To prevent this, do not
plug the TX-NR1000/TX-NR5000E into the same
circuit used by sensitive equipment, e.g., computers.
2
STANDBY indicator [9, 50]
Lights when the TX-NR1000/TX-NR5000E is in
the standby state and when a signal is received from
the remote controller.
the standby state and when a signal is received from
the remote controller.
3
STANDBY/ON button [50]
If pressed with the [POWER] switch turned on (with
the receiver plugged in for USA, Canadian, and
Australian models), the TX-NR1000/TX-NR5000E
turns on and the display lights up. If pressed again, the
TX-NR1000/TX-NR5000E returns to the standby
state. In the standby state, the display is turned off and
the TX-NR1000/TX-NR5000E cannot be operated.
the receiver plugged in for USA, Canadian, and
Australian models), the TX-NR1000/TX-NR5000E
turns on and the display lights up. If pressed again, the
TX-NR1000/TX-NR5000E returns to the standby
state. In the standby state, the display is turned off and
the TX-NR1000/TX-NR5000E cannot be operated.
4
Remote control sensor [9]
5
DISPLAY button [54]
Press to display information about the current input
source signal. Each time you press the [DISPLAY]
button, the screen changes to show you different
information concerning the input signal.
source signal. Each time you press the [DISPLAY]
button, the screen changes to show you different
information concerning the input signal.
6
Front display
7
Input source buttons and indicators (DVD,
VIDEO 1–7, TAPE 1-2, TUNER, PHONO, CD,
and NET AUDIO) [50, 60, 63, 76]
VIDEO 1–7, TAPE 1-2, TUNER, PHONO, CD,
and NET AUDIO) [50, 60, 63, 76]
Press these buttons to select the input source for the
main zone.
After selecting the input source, the corresponding
indicator turns blue. If you select Zone 2, the
indicator turns green. If you select Zone 3 or Rec,
the indicator turns red.
main zone.
After selecting the input source, the corresponding
indicator turns blue. If you select Zone 2, the
indicator turns green. If you select Zone 3 or Rec,
the indicator turns red.
8
MASTER VOLUME dial [50]
Use to control the volume in the main zone. The
volume for the remote zone (Zone 2 and Zone 3) is
independent.
volume for the remote zone (Zone 2 and Zone 3) is
independent.
9
OPEN button
Press this button to open the front panel door.
0
PURE AUDIO indicator [59]
Lights during pure audio playback.