ONKYO TX-NR1000 Manual Do Utilizador

 

88

 

The TX-NR1000/TX-NR5000E provides a wide range of variations in speaker connections and speaker settings, so you 
have to specify speaker settings according to conditions of each variation. For proper selection of an AV device 
connected at switching of the input type, you also need to allocate “audio output” and “video output” to each input type. 
If this allocation is incorrect, the desired component will not play a selected input source.
Please setup correctly by referring to the information you wrote down in the Your System Settings booklet.

Specify the rooms where you want to use speakers 
connected to the SPEAKERS A terminal and the 
SPEAKERS B terminal. Specify according to settings 
for main room A.

 

Basically, a speaker set with the maximum number of 
speakers should be connected to the SPEAKERS A 
terminals and configured for main room A (Main A). 
When either the center, surround, or surround back 
speakers are not connected to the SPEAKERS A 
terminals, or any of these speakers is set to “Not Used” 
in the Speaker A settings, you cannot perform the 
settings for the corresponding speakers connected to the 
SPEAKERS B terminals and those speakers connected 
to the SPEAKERS B terminals cannot be used.

 

The setting of the front speakers is initially fixed to 
Main A.
Always install speakers connected to FRONT L/R of 
SPEAKERS A in main room A.

 

 Select this when using the center 

speaker and/or surround speakers in main room A.

 

 Select this when not using a center speaker 

or surround speakers.

 

If Surr L/R is set to “Main A,” 

you can select this item. Select this when connecting 
and using two surround back speakers in main room A.

 

If Surr L/R is set to “Main A,” you 

can select this item. Select this when connecting and 
using a surround back speaker in main room A. 

 

 Select this when using the front 

speaker in main room A by connecting the surround 
back channel to the speaker via BTL (See page 27).

 

 Select this when using the front 

speaker in main room A by connecting the front channel 
and the surround back channel to the speaker via Bi-
Amp (See page 27). 

 

 Select this when not using surround back 

speakers. 

 

If “Not Used” is selected for Surr L/R, this item defaults 
to “Not Used.” 

 

 Select this when using a subwoofer 

in main room A. 

 

Select this when not using a subwoofer in 

main room A. 

 

Select this when using in main room A. 

 

Select this when using in main room B. 

 

Select this when not using. 

 

 Select this when using in main room A. 

 

 Select this when using in main room B. This 

setting can only be made when you set the “(Speaker B) 
Front L/R” setting to “Main B.”

 

 Select this when not using. 

 

 Select this when using in main room A. 

 

 Select this when using in main room B. This 

setting can only be made when you set the “(Speaker B) 
Front L/R” setting to “Main B.”

 

 

 

 Select this when not using. 

 

Select this when connecting and using two 

surround back speakers in main room A. 

 

 Select this when connecting and 

using a surround back speaker in main room A. 

 

 If (Speaker B) Front L/R and Surr L/R are 

both set to “Main B,” you can select this item. Select 
this when connecting and using two surround back 
speakers in main room B. 

 

If (Speaker B) Front L/R and Surr 

L/R are both set to “Main B,” you can select this item. 
Select this when connecting and using a surround back 
speaker in main room B. 

 

 Select this when using in Zone 2.

• If (Speaker A) Surr Back is set to “BTL for Front” or 

“Bi-Amp for Front,” this item is not displayed 
(Because, if “Powered Zone 2” is set, BTL 
connection and/or Bi-Amp connection are disabled). 

 

 This setting can be made only when 

you set the “(Speaker B) Front L/R” setting to “Main A” 
or “Main B.” Select this when using the front speaker in 
main room B by connecting the surround back channel 
to the speaker via BTL (See page 27).