ONKYO TX-NR1000 Manual Do Utilizador

98

Input Setup—Continued

When multiple devices are connected to the 
TX-NR1000/TX-NR5000E, the volume may vary for a 
device even when volume settings on the TX-NR1000/
TX-NR5000E are identical.
Reducing the variance in the volume level will allow 
you to enjoy sounds at the same volume level without 
adjusting the volume control on the TX-NR1000/
TX-NR5000E. 

Use the [

] button when the volume is louder than 

other devices, and the [

] button when the volume is 

quieter. 
You can set at 0.5 dB intervals within a range from 
–12.0 dB to +12.0 dB. The default is 0.0 dB. 

This section describes how to adjust the delay of 
sounds. 

When the picture is not synchronized with the sound, 
you can synchronize them using these settings. This 
option can be set for Main B and Zone 2 as well as for 
Main A.
You can set at 0.1 ms intervals within a range from 0.0 
ms to 300.0 ms. 

Our proprietary “Enhanced Special Positioning 
Algorithm” (an extended three-dimensional positioning 
algorithm) fine tunes the sound field. This algorithm is 
able to create a maximum delay of 10 ms in the output 
of each speaker. This delay is equivalent to a distance of 
about 3 meters between speakers. This option can be set 
for both Main A and Main B.
• When “Center” is set to “Not Used” on the Speaker 

Configuration sub-menu, there is no setting for 
“Center.” Likewise, if “Surr L/R” is set to “Not 
Used,” or “Surr Back” is set to “BTL for Front,” “Bi-
Amp for Front,” or “Not Used,” there is also no 
setting for corresponding speakers.

You can set at 0.1 ms intervals within a range from 
–10.0 ms to +10.0 ms. The default is 0.0 ms. 
Use this function to fine tune your surround 
environment after setting the distance between speakers 
(See page 89) and the volume level (See page 90). 
Extending the distance between speakers (widening the 
delay in time) will expand the sound field, while 
reducing the distance (narrowing the delay) will make 
the sound field sharper. 

When the 12V TRIGGER OUT jack on the 
TX-NR1000/TX-NR5000E is connected to the 12V 
TRIGGER IN jack of a device, you can specify the 
room where you are going to trigger the device to turn 
on the power (for connection details, see page 46).
The default settings are as follows: 

The following are settings for the 12V trigger jacks A-
E: 
Off: Select when not using. 
Main: Select when you want to power on a connected 
device only used in the main room. 
Zone 2: Select when you want to power on a connected 
device only used in Zone 2. 
Zone 3: Select when you want to power on a connected 
device only used in Zone 3. 
Main/Zone 2: Select when you want to power on a 
connected device only used in the main room or Zone 2. 
Main/Zone 3: Select when you want to power on a 
connected device only used in the main room or Zone 3. 
Zone 2/Zone 3: Select when you want to power on a 
connected device only used in Zone 2 or Zone 3. 
Main/Zone 2/Zone 3: Select when you want to power 
on a connected device used in any area: main room, 
Zone 2, or Zone 3. 

When a 12V trigger-connected device is powered on, a 
large amount of current may, depending on the device 
type, flow instantaneously. To ease the effects of this 
problem, you can set time interval differences for output 
signals from the 12V Trigger.
Setting time interval differences may prevent 
unnecessary noise (bubbling sounds).
0 sec: Select when not setting any difference. 
1 sec: Select when setting output signals 1 second after 
power on to the TX-NR1000/TX-NR5000E. 
2 sec: Select when setting output signals 2 seconds after 
power on to the TX-NR1000/TX-NR5000E. 
3 sec: Select when setting output signals 3 seconds after 
power on to the TX-NR1000/TX-NR5000E.

Trigger A

Main

0

Trigger B

Zone 2

1

Trigger C

Zone 3

2

Trigger D

Off

0

Trigger E

Main

2