Panasonic SC-PMX70 Manual Do Utilizador

RQT9

98

8

• For some built-in Bluetooth

®

 devices, you have to set 

the audio output to “SC-PMX70” manually. Read the 

operating instructions for the device for details.

• The device is out of the 10 m communication range. 

Bring the Bluetooth

®

 device closer to this system.

• Remove any obstacle between this system and the 

device.

• Other devices that use the 2.4 GHz frequency band 

(wireless router, microwaves, cordless phones, etc.) 

are interfering. Bring the Bluetooth

®

 device closer to 

this system and distance it from the other devices.

• Select “MODE 1” for stable communication. (> 7)
The One-Touch Connection (NFC feature) is not 

• Make sure the unit and the NFC feature of the device 

are turned on. (> 6)

• You connected the AC mains lead for the first time or 

there was a power failure recently. Set the clock.

• Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”

• Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”

• The unit has been left unused for about 20 minutes 

and will shut down in a minute. Press any button to 

cancel it.

• The unit is checking the connected iPhone/iPad/iPod 

or USB device.

• If this display keeps appearing, make sure that the 

battery of the iPhone/iPad/iPod is not depleted and 

that the iPhone/iPad/iPod is turned on and connected 

correctly.

• An incorrect operation was done. Read the instructions 

and try again.

“F” (“  ” stands for a number.)

• There is a problem with this unit.

Write down the displayed number, disconnect the AC 

mains lead and consult your dealer.

• The iPhone/iPad/iPod or USB device is not connected.

Examine the connection.

• The battery of the iPhone/iPad/iPod is depleted. 

Charge the iPhone/iPad/iPod and turn it on before 

connecting.

• You have not put in a disc or put in a disc that the 

system cannot play.

“NO MEMORY” ([PMX70B])

• There are no preset DAB stations to select. Preset 

some channels.

• Examine the content. You can only play supported 

format.

• The files in the USB device can be corrupted. Format 

the USB device and try again.

• The unit may have a problem. Turn the unit off and 

then on again.

“NO SIGNAL” ([PMX70B])

• This station cannot be received. Check your antenna.
“DEVICE NO RESPONSE”

• You have connected an iPhone/iPad/iPod that cannot 

be played.

• If the iPhone/iPad/iPod is compatible, turn it on and 

connect it correctly.

• You have connected an unsupported USB device.
“PGM FULL”

• The number of programmed tracks is more than 24.
“PLAYERROR”

• You played an unsupported file. The system will skip 

that track and play the next one.

• The unit is checking the CD information. After this 

display has disappeared, start operating.

“REMOTE ” (“  ” stands for a number.)

• The remote control and this unit are using different 

codes. Change the code on the remote control.

– When “REMOTE 1” is displayed, press and hold [OK] 

and [1] for at least 4 seconds.

– When “REMOTE 2” is displayed, press and hold [OK] 

and [2] for at least 4 seconds.

“SCAN FAILED” ([PMX70B])

• Stations are not receivable. Check your antenna and try 

DAB manual tuning.

• The iPhone/iPad/iPod or USB device is drawing too 

much power. Remove the iPhone/iPad/iPod or USB 

device. Switch the system off and on again.

• The system cannot show the remaining play time for 

variable bit rate (VBR) tracks.

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

Disconnect the AC mains lead.
Wait 3 minutes before you continue with step 2.

While you press and hold [Í/I] on the main unit, 
connect the AC mains lead again.
“- - - - - - - - - ” is shown.

Release [Í/I].
All the settings are set back to the factory default.

It is necessary to set the memory items again.

When other Panasonic equipment responds to the 

remote control of this system, change the remote control 

code for this system.
To set the code to “REMOTE 2”

• The factory default is “REMOTE 1”.

• To change the mode back to “REMOTE 1”, repeat the 

steps above but replace the button pressed on the 

remote control from [2] to [1].

SC-PMX70-70B_EGEBGN-RQT9988-B.book  13 ページ  ２０１４年１２月２９日　月曜日　午後１時２１分