JVC KD-AR470 Manual Do Utilizador
A
2
Typical Connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
External Component
*
7
Line Input Adapter KS-U57 (not supplied for this unit)
Connecting the external amplifier
You can connect amplifiers to upgrade your
car stereo system.
• Connect the remote lead (blue with white
car stereo system.
• Connect the remote lead (blue with white
stripe) to the remote lead of the other
equipment so that it can be controlled
through this unit.
equipment so that it can be controlled
through this unit.
• Disconnect the speakers from this unit,
connect them to the amplifier. Leave the
speaker leads of this unit unused.
speaker leads of this unit unused.
*
3
Firmly attach the ground wire to the metallic body
or to the chassis of the car—to the place not coated
with paint (if coated with paint, remove the paint
before attaching the wire). Failure to do so may cause
damage to the unit.
with paint (if coated with paint, remove the paint
before attaching the wire). Failure to do so may cause
damage to the unit.
• Set “EXT IN” for the external input setting (see page 13 of the INSTRUCTIONS.)
CAUTION:
• Before connecting the CD changer, make
sure that the unit is turned off.
*
4
Signal cord (not supplied for this unit)
External component
3.5 mm stereo mini plug
B
Rear speakers
JVC Amplifier
Remote lead
Y-connector (not supplied for this unit)
Remote lead (Blue with white stripe)
To the remote lead of other
equipment or auto antenna if any
equipment or auto antenna if any
Front speakers
External component
ELECTRICAL CONNECTIONS
CD changer jack
Line out (see diagram )
Rear ground
terminal
15 A fuse
Black
Blue with white stripe
Red
Yellow
*
2
To metallic body or chassis of the car
Ignition switch
Fuse block
To an accessory terminal in the fuse block
To the remote lead of other equipment (200 mA max.)
Right speaker (rear)
Purple
Left speaker (rear)
Purple with black stripe
Green
Right speaker (front)
Green with black stripe
Gray
Left speaker (front)
Gray with black stripe
White
White with black stripe
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
(bypassing the ignition switch) (constant 12 V)
Orange with white stripe
To car light control switch
Antenna terminal
To CD changer or another external component (see diagram )
*
1
Not supplied for this unit.
*
2
Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
power cannot be turned on.
Blue
To the automatic antenna if any (250 mA max.)
CD changer, Apple iPod
®
, or JVC D. player
You can connect these components as illustrated below. The iPod*
5
or D. player can
be connected using an interface adapter (not supplied)—KS-PD100 (for iPod) or
KS-PD500 (for D. player).
KS-PD500 (for D. player).
*
6
Connecting cord supplied for your CD changer
Connecting the external components
C
• Set “CHANGER” for the external input setting (see page 13 of the INSTRUCTIONS.)
Apple iPod
(separately purchased)
(separately purchased)
JVC D. player
(separately purchased)
(separately purchased)
CD changer jack
JVC CD changer
*
5
iPod is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries.
registered in the U.S. and other countries.
*
8
AUX Input Adapter KS-U58 (not supplied for this unit)
or
Install_KD-G524[UI]f.indd 2
Install_KD-G524[UI]f.indd 2
9/13/05 6:41:59 PM
9/13/05 6:41:59 PM