Kenwood KDC-BT60U Manual Do Utilizador
42
|
KDC-BT60U/ KDC-6047U
DSP Setup
Press the [MENU] button for at least 1 second,
and then press it again briefly.
and then press it again briefly.
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
Refer to the following operations to setup the
Sound Control.
- Car Type Selection (page 40)
- Speaker Setting (page 40)
- Car Type Fine Adjustments (page 41)
- X’Over Setting (page 42)
- Manual Equalizer Control (page 37)
- Listening Position Selection (page 38)
- Listening Position Fine Adjustments (page 38)
- Speaker Setting (page 40)
- Car Type Fine Adjustments (page 41)
- X’Over Setting (page 42)
- Manual Equalizer Control (page 37)
- Listening Position Selection (page 38)
- Listening Position Fine Adjustments (page 38)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
>
“Preset”
>
“Memory”.
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
• Preset number “1”:
When you press the Reset, all the sources will be the
setting value which is registered.
setting value which is registered.
• Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod
Equalizer set in
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
corresponding to the X’Over values set in the
section
.
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear”
“FC”
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC”
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250*, Through (Hz)
“SLOPE”
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍
SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
repeatedly switches source.
2
Enter Audio Control mode
Press the [VOL] knob.
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup”
>
“X’Over”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the item you want to set
Operation type
Operation
Selects the item.
Turn the [VOL] knob.
Adjust each item.
Press the [
4] or [¢] button.
Set the value
Press the [VOL] button.
6
Repeat steps 3 to 4 to complete the X’Over
settings.
settings.
7
Exit Audio Control mode