Kenwood DPX 504 U Manual Do Utilizador
56
|
DPX504U/ DPX404U/ DPX304
DSP Setup
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
-
Refer to the following operations to setup the
Sound Control.
-
-
-
-
-
-
-
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
>
“Detailed Setup”
>
“Preset”
>
“Preset Memory”.
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
Press the [ ] button for at least 1 second.
⁄
•
Register 6 patterns of Audio Preset Memory.
•
Preset number “1”:
When you press the Reset, all the sources will be the setting
value which is registered.
When you press the Reset, all the sources will be the setting
value which is registered.
•
Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
The memory cannot be erased by the Reset button.
•
This function cannot be registered when the iPod Equalizer
set in
set in
.
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
corresponding to the X’Over values set in the
section
.
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear”
“FC”
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC”
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE”
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Press the [SRC] button.
Select a source other than “STDBY”.
2
Enter Function setting mode
Press the [VOL] knob.
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
>
“Detailed Setup”
>
“X’Over”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the item you want to set
Operation type
Operation
Selects the item.
Turn the [VOL] knob.
Adjust each item.
Press the [
4] or [¢] button.
Set the value
Press the [VOL] knob.
6
Repeat steps 4 to 5 to complete the X’Over
settings.
settings.
7
Exit Function setting mode
Press the [ ] button for at least 1 second.
Press the [ ] button for at least 1 second.
Function of DPX504U