B&K Series 2 Manual Do Utilizador
TROUBLESHOOTING
58
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
No sound
Display will not
illuminate.
Display will not
illuminate.
1. Power cord not plugged in.
2. Power off at AC source.
3. AC power inlet fuse blown or
faulty.
4. Power switch in off position (out).
2. Power off at AC source.
3. AC power inlet fuse blown or
faulty.
4. Power switch in off position (out).
1. Reconnect power cord.
2. Check AC switch or fuse.
3. Check AC line fuse, replace line fuse with
2. Check AC switch or fuse.
3. Check AC line fuse, replace line fuse with
.5A 250V Fast Blow fuse.
4. Push in the main power switch.
No sound
Unit display will
illuminate.
Unit display will
illuminate.
1. Preamplifier is in mute.
2. Volume control to a minimum.
3. Un-used source selected.
4. Line stage or source not correctly
connected.
5. Speaker fuse blown.
2. Volume control to a minimum.
3. Un-used source selected.
4. Line stage or source not correctly
connected.
5. Speaker fuse blown.
1. Un-mute the preamplifier .
2. Turn up volume.
3. Select an active source.
4. Check ALL connections. Try substituting
cables.
5. Check all speaker fuses and replace if blown.
Replace fuse with same type and value.
2. Turn up volume.
3. Select an active source.
4. Check ALL connections. Try substituting
cables.
5. Check all speaker fuses and replace if blown.
Replace fuse with same type and value.
Loud hum or buzz on
one or more channels.
Channel sounds “bad.”
one or more channels.
Channel sounds “bad.”
1. Poor ground connection in the
interconnect cables.
2. Poor AC ground in main AC supply
3. Audio cables installed across AC
power.
interconnect cables.
2. Poor AC ground in main AC supply
3. Audio cables installed across AC
power.
1. Check all connections making sure that
cables are connected (+) to (+) and (-) to (-).
2. Check all cables and repair where necessary.
3. Reposition cables, bundle like cables
together.
4. Try substituting cables.
cables are connected (+) to (+) and (-) to (-).
2. Check all cables and repair where necessary.
3. Reposition cables, bundle like cables
together.
4. Try substituting cables.
Remote / Keypad / IR
sensor(s) will not work.
sensor(s) will not work.
1. Batteries dead, missing, installed
wrong.
2. IR lock is enabled
3. IR inference.
4. Using the wrong IR code-set.
5. Wires are crossed
wrong.
2. IR lock is enabled
3. IR inference.
4. Using the wrong IR code-set.
5. Wires are crossed
1. Check and replace batteries.
2. Unlock IR sensor, see Advanced Security
menu.
3. Check for nearby sunlight, plasma TV’s or
fluorescent light. Block where needed.
4. Check zone assigned IR code-set.
5. Check wiring diagram on
2. Unlock IR sensor, see Advanced Security
menu.
3. Check for nearby sunlight, plasma TV’s or
fluorescent light. Block where needed.
4. Check zone assigned IR code-set.
5. Check wiring diagram on
Surround speakers are
not very loud in
SURROUND mode.
not very loud in
SURROUND mode.
1. Normal operation.
2. Speaker channels may not be
turned on.
2. Speaker channels may not be
turned on.
1. When in SURROUND Mode, most audio
information is directed to the center channel.
Surround and back channels are used for
“effects” scenes.
2. Check speaker setup
information is directed to the center channel.
Surround and back channels are used for
“effects” scenes.
2. Check speaker setup
Unit is locked
1. Poor power supply
2. Processor lockup
2. Processor lockup
1. Check AC power and cold boot.
2. Cold boot (power switch) or reset the unit.
2. Cold boot (power switch) or reset the unit.
No component video
1. Component video input is not
assigned.
assigned.
1. Assign the component video to the appro-
priate source input.
priate source input.
S-Video and Composite
video not visible when
using DVD player.
video not visible when
using DVD player.
1. DVD player set to progressive
scan.
scan.
1. Progressive scan (480p) can only be viewed
using component video.
2. Reset DVD player to interlaced (480i).
using component video.
2. Reset DVD player to interlaced (480i).
Preamplifier is not
recognizing multi-
channel bitstreams.
recognizing multi-
channel bitstreams.
1. DVD player needs to be config-
ured for digital output.
ured for digital output.
1. Go into the DVD players setup menu and
turn on the appropriate digital output.
turn on the appropriate digital output.