Panasonic CQ-CB8901U Manual Do Utilizador

13

12

¡

Adjust the clock when “ADJUST” appears on the
display.

Press [MENU] to display the menu

display.

For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.

Press []] or [[] to display the

DISPLAY menu.

Press [

{

] to select “CLOCK ADJ”.

Press [BAND] (SET) to confirm the

display.

Adjust the setting value.

[[]

: Adjusting minutes

[]]

: Adjusting hours

}

: Forward

{

: Backward

Press [BAND] (SET) to confirm the

adjustment.

Press [MENU].

For using the remote control, hold down [SEL]
(MENU) for 2 sec. or more.

The demonstration message appears for first use.

Set your car's ignition switch to the ACC

or On position.

The demonstration screen appears.

Press [DISP] (Display).

The demonstration screen is cancelled, and no more
appears.

Press [SRC] (PWR: Power).

Note: If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: Power) for 4 sec. or more after turning off the
power in other than the XM mode.

You may need to set the following depending on the
devices to be connected.

¡

Subwoofer level adjustment (

a

page 34)

¡

Subwoofer low pass filter (

a

page 34)

¡

High Pass Filter (

a

page 34)

¡

Connect the optional XM receiver (XMD1000).

¡

To connect the XM receiver (XMD1000), it is required
to use an optional extension cord (XMDPAN100) that is
produced by XM exclusively for Panasonic products.

It is required to sign up to become an XM Satellite
Radio subscriber. After checking your XM Satellite
Radio ID, sign up on the XM’s website or by calling
them.

Check of XM Satellite Radio ID

¡

Write down the ID indicated on the lower right of your
XM receiver (XMD1000).

¡

Radio ID also can be found by turning your XM Radio
to channel 0. (Refer to “Channel Selection” on page
28.)

Activate the XM Satellite Radio

Select either of the below to sign up.

¡

Web site: http://www.xmradio.com/activation

¡

Phone number: 1-800-852-9696

Note: Refer to the operating instructions for the XM
receiver for details.

The following functions are activated when the Security
Function is ON. (

a 

page 35)

¡

The security indicator lights up when removing the
face plate.

¡

The alarm sounds and the message appears on the
screen to warn you to remove the face plate at ACC
off.

Security Indicator

CQ-CB8901U

(DEMONSTRATION)

¡

Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.

¡

Remove and dispose of an old battery immediately.

¡

Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.

¡

Follow local regulations when disposing of a battery.

¡

Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.

Note: Battery Information:

Battery Type: Panasonic lithium battery (CR2025)

(Included in the remote control)

Battery Life : Approximately 6 months under normal use

(at room temperature)

Pull the insulation film out
from the backside of
remote control gently.

q

w

q Remove the battery holder

with the remote control unit
placed on a flat surface.
q Stick your thumbnail into

the groove, and push the
holder in the direction of
the arrow, and at the
same time.

w Pull it out in the direction

of the arrow using a
tough pointed object.

2

3

w Put a battery in the case

with (+) side facing up.

e Put the case back.

Tough pointed object

Back side

Insulation film