Toshiba IK-7200A Folheto

- 6 -

Notes:

The attached screws and anchors are used to install the camera to a solid 

• 

surface. (e.g. concrete) If installing to loose or thin material surfaces , use 

the appropriate anchors (not included) with the screws.
Install the camera tightly.

• 

3-1 Mounting the camera to a solid surface

(1)   Attach the Alignment Sticker to the surface.
(2)   Drill  three  pilot  holes  (Ø0.28inch×1.57inches(D)(Ø7mm×40mm(D))) 

through the three circles on the sticker.

(3)   Hammer the supplied plastic anchors into the holes.
(4)   Drill a hole (Ø0.63inch(Ø15mm) in the center of the sticker, and lead the 

video and power cables in this hole.

(5)   Align the three holes of the Mounting Bracket with the three plastic anchors; 

insert the supplied screws with camera to corresponding holes.

3-2 Adjusting the view angle and lens

(1)  The camera direction can be adjusted horizontally (pan: max. 360 deg.) 

and vertically (tilt: max. 90 deg.).

(2)  To adjust pan and tilt rotate the Clamp Ring counterclockwise, and loosen 

the two Locking Screws using a screwdriver.

Alignment Sticker

Anchor

Clamp Ring

Screw

Locking Screw

1. Replace original screw 

by  hexagonal  screw 

of  accessories,  and 

temporarily fix it.

2. Adjust the shade to the 

best position.

3. Secure  this  screw  by 

using  a  wrench  (not 

included).

- 7 -

(3)  Turn the camera to the desired position, rotate the Clamp Ring clockwise to 

secure the camera.

(4)  To adjust zoom and focus, loosen two controller screws, and move them to 

the desired position.

(5)  Tighten zoom and focus controller screws. To secure these screws tightly, 

be sure to tighten them using a screwdriver.

(6)  To secure the camera tightly, be sure to tighten the two Locking Screws 

using a screwdriver.

Adjust the shade position after replacing original screw by hexagonal screw 

• 

of accessories.
 Be sure to securely tighten the Clamp Ring.

• 

AGC  and  BLC  selecting  switches  are  internally-located.To  adjust  these 

switches,  rotate  the  cap  counterclockwise.  After  adjusting,  rotate  the  cap 

clockwise. Make sure that the cap has been tightly secured to the camera using 

a screwdriver.
(1)  Backlight Compensation (BLC)
 

 The exposure is automatically adjusted so that the best picture is obtained 

at a monitor zone of about 50% in the horizontal and about 50% in the  

vertical directions. The factory setting is "ON".

(2)  Auto Gain Control (AGC)
 

 Camera maximum gain can be selected High (30dB) or Low (24dB). The 

factory setting is "High". If the image is noisy in low-light, change this switch 

to "Low".

This camera is equipped with near-infrared LEDs (IR LED) of 850nm. The LEDs 

turn on automatically when it becomes dark. (The human eye cannot clearly 

see the light of the LEDs.)
This camera is able to clearly produce monochrome images at a range of less than 

82 feet.

- 8 -

Do not aim the camera at the sun

• 

 

Never aim the camera at the sun even with the camera power off.

Do not shoot intense light

• 

 

 Intense light such as a spotlight may cause a bloom or smear. A vertical stripe 

may appear on the screen. However, this is not a malfunction.

Treat the camera with care

• 

 

Do not drop the camera or subject it to intense vibration.

Never touch internal parts

• 

 

Do not touch the internal parts of the camera other than the parts specified.

Do not submerge in water

• 

 

 Install the camera where the camera can be used indoors or outdoors according 

to IP66 code. If the camera was dropped in the water, turn off the power and 

contact your dealer.

Keep the camera installation away from video noise

• 

 

 If cables are wired near electric lighting wires or a TV set, noise may appear in 

images. In this event relocate cables or reinstall equipment.

Check the ambient temperature and humidity

• 

 

 Avoid  using  the  camera  where  the  temperature  is  hotter  or  colder  than  the 

specified operating range. Doing so could affect the internal parts or cause the 

image quality to deteriorate. Special care is required to use the camera at high 

temperature and humidity.

Should you notice any trouble

• 

 

 If any trouble occurs while you are using the camera, turn off the power and 

contact your dealer. If you continue to use the camera when there is something 

wrong with it, the trouble may get worse and an unpredictable problem may occur.

Condition

Check Points

No image

•  Are the camera and connected equipment turned on?
•  Are wires connected correctly?

Unnatural color

•  Is the display monitor adjusted correctly?
•  Is the lighting too dim? 

Flicker noise

•  Under the fluorescent lamp of 60Hz, flicker noise rarely occurs.

Defocusing at night

•  Readjust the focus at night-mode that turned on the IR LED.

- 9 -

1. Image System

Image Device

1/3 inch CCD image sensor

Pixel Elements

768 (H) x 494 (V)

2. Electrical

TV System

NTSC
2:1 Interlace, 15.734 kHz horizontal, 59.94 Hz vertical

Horizontal Resolution

480 TV lines (typical)

S/N Ratio

48 dB

Minimum Illumination

0 lux (LED is ON)

Gain Control

AGC:High (30dB), Low(24dB)

White Balance

Auto

White Balance Range

2,500 K to 9,500 K

Auto Electronic Shutter

1/60 s to 1/100,000 s

Backlight Compensation (BLC) ON / OFF
Video Output Signal

VBS (1.0 Vp-p, 75 ohms unbalanced, BNC)

Synchronization System

Internal

IR LED

36 LEDs, 850nm

IR Distance

82 feet (25m)

3. Mechanical

Weight

1.4 lbs (630 g)  camera only

Dimension

3.2(W) x 3.1(H) x 5.4(D) inches (81.5mm(W) x 79.5mm(H)  
x 137.5mm(D)  (excluding protrusion and mounting bracket))

Ingress Protection Rating IP66

4. Optical

Built-in Lens

f = 3.7-10 mm, F 1.6

View Angle of Lens

27-77°(H),   21-57°(V)

5. Power

Input Voltage

12V DC ±10 %

Current Consumption

0.4A (MAX.)

- 10 -

6. Environmental

Operating Temperature
and humidity

14°F to 122°F (-10°C to +50°C )
20 % to 90 % RH

Storage Temperature
and humidity

-4°F to 140 °F (-20°C to 60°C)
90 % RH

Design and specifications are subject to change without notice.

120°

120°

Ø2.4

（Ø62）

3-Ø0.2

（Ø5）

1

（25）

2.1

（

54

）

0.24

（6）

4.2

（106）

3.2

（81.5）

Ø2.8

（Ø70）

5.4

（137.5）

3.1

（

79.5

）

Dimensions: Inch (mm)

- 11 -

CCD SECURITY CAMERA IK-7211A

The Imaging System Division (“ISD”) of Toshiba America Information Systems,Inc.makes the following limited warranties with regard to this 

CCD Camera Model IK-7200A (“Product”).These limited warranties extend to the Original End-User (“You [r]”).
Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a 

period of three (3) years from the date of purchase by the Original End-User. During this three (3) year period, ISD will repair or replace the 

Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call (877) 855-1349 to receive a 

RMA number:and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center. ISD 

reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner's Manual) :You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product. 

Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the 

instructions to correct the problem.
How to Obtain Warranty Service Step-by-step Procedures :To obtain warranty service. You should :
1.  Contact Toshiba America Information Systems, Inc. at (877) 855-1349 to first verify operation or installation assistance. (877) 855-1FIX

2.  If technical support determines that the unit is defective,an RMA will be issued with return instructions for repair.

3.  Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the bill of 

sale or proof of purchase.

4.  Prepay all transportation and insurance costs.
Your Responsibilities: This Limited Warranty is subject to the following conditions:
1.  You must provide the bill of sale or proof of purchase at the time that warranty service is required.

2.  You must notify Toshiba America Information Systems, Inc. at (877) 855-1349 within (30) days after you discover that the product does not 

perform in accordance with specifications during the Limited Warranty period.

3.  You must pack the Product in its original carton using the original packing material.Then insert the original carton containing the Product 

into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.

DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW 

THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE 

LIMITATIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE 

THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE 

TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION 

APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR 

OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR 

OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT 

COMPANY, OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY. 

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME 

PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE 

TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE, ABUSE, ACCIDENT, 

IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD'S WRITTEN INSTRUCTIONS, OR WHERE THE 

PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION 

OF ISD'S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF 

CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY.
No person, agent, distributor,dealer,authorized service provider, or company is authorized to change, modify, or extend the terms of this 

Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising 

under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the date 

You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.

Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so the above 

provision may not apply to You. This Limited Warranty gives You spacific legal rights and You may also have other rights which vary from state 

to state.

TOSHIBA AMERICA INFORMATION SYSTEMS, INC1

Imaging Systems Division