Bosch PT-400 Manual Do Utilizador
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
and Screens
EN | 46
Bosch Security Systems | 6/12 | 38947D
Successful Incoming Messages
The total number of messages
successfully received from this
transponder.
Incoming Format Errors
The number of messages received from
this transponder where format error was
detected. This field is yellow if 1.5%
or more of the messages had errors. A
high level of message errors indicates
a serious communication problem.
Incoming Retried Messages
The total number of messages
successfully received from this
Transponder that indicated they were
retried. This field is yellow if 1.5%
or more of the messages are retried. A
high level of retried messages
indicates a serious communication
problem.
Total Outgoing Messages
The total number of messages sent to
this transponder from the central
console.
Outgoing Retried Messages
The total number of message retries to
this transponder. This field is yellow
if 1.5% or more of the messages are
retried. A high level of retried
messages indicates a serious
communication problem.
Outgoing Failed Messages
This is total number of messages that
could not to be delivered to this
transponder. This field is yellow if
there are any failed messages. Outgoing
failed messages cause the central
console to display an alert message
that communications have failed.
Stress Test
This checkbox causes the central
console to continually request maps
from the transponder. When in this
mode, the central console sends a new
map request as soon as it receives a
map from the transponder, rotating
through the map types. This test is
used when diagnosing communications
problems to create artificially high
traffic on the communication link
without interfering with the processing
of alarms and tests. The stress test
ceases when the checkbox is cleared, or
this screen is closed by clicking the
Cancel button.
The total number of messages
successfully received from this
transponder.
Incoming Format Errors
The number of messages received from
this transponder where format error was
detected. This field is yellow if 1.5%
or more of the messages had errors. A
high level of message errors indicates
a serious communication problem.
Incoming Retried Messages
The total number of messages
successfully received from this
Transponder that indicated they were
retried. This field is yellow if 1.5%
or more of the messages are retried. A
high level of retried messages
indicates a serious communication
problem.
Total Outgoing Messages
The total number of messages sent to
this transponder from the central
console.
Outgoing Retried Messages
The total number of message retries to
this transponder. This field is yellow
if 1.5% or more of the messages are
retried. A high level of retried
messages indicates a serious
communication problem.
Outgoing Failed Messages
This is total number of messages that
could not to be delivered to this
transponder. This field is yellow if
there are any failed messages. Outgoing
failed messages cause the central
console to display an alert message
that communications have failed.
Stress Test
This checkbox causes the central
console to continually request maps
from the transponder. When in this
mode, the central console sends a new
map request as soon as it receives a
map from the transponder, rotating
through the map types. This test is
used when diagnosing communications
problems to create artificially high
traffic on the communication link
without interfering with the processing
of alarms and tests. The stress test
ceases when the checkbox is cleared, or
this screen is closed by clicking the
Cancel button.
Auto Scan
The auto scan function performs the
above stress test proceeding from one
transponder to the next after one of
each type of map is requested and
received. After the last map type and
before proceeding to the next
transponder, a command is issued to
refresh the transponder data so that
when an auto scan is proceeded through
all transponders, all transponder and
point troubles are updated. Auto scan
is terminated by removing the check in
the Auto Scan box or by closing the
screen using the Cancel button.
Current Troubles
This window displays all current
troubles for this transponder. In the
Current Transponder Status Screen,
there is a low battery and a tamper
condition being reported for this
transponder. This window also displays
the restoration to a normal condition
when it occurs. When the fault is
corrected, clicking the Acknowledge
button eliminates any Restoration
Reports. Conditions, which were not
rectified, remain in the window.
Not Responding Map
To assist in diagnosing problems with
the receivers and alert units
associated with a transponder, several
commands can be issued from the central
console to requesting information from
the transponder. This button requests a
map of all the devices on this
transponder (receivers or alert units)
that are not responding to the system.
The current troubles list is
automatically updated.
Jamming Map
This button requests a map of all the
receivers on this transponder that are
reporting a jamming condition to the
system. The Current Troubles list is
automatically updated.
Previous
Returns to the previous transponder.
Next
Advances to the next transponder.
Out of Service Map
This button requests a map of all
devices on this transponder (receivers
or alert units) that were manually
taken out of service to the system. The
current troubles list is automatically
updated.
The auto scan function performs the
above stress test proceeding from one
transponder to the next after one of
each type of map is requested and
received. After the last map type and
before proceeding to the next
transponder, a command is issued to
refresh the transponder data so that
when an auto scan is proceeded through
all transponders, all transponder and
point troubles are updated. Auto scan
is terminated by removing the check in
the Auto Scan box or by closing the
screen using the Cancel button.
Current Troubles
This window displays all current
troubles for this transponder. In the
Current Transponder Status Screen,
there is a low battery and a tamper
condition being reported for this
transponder. This window also displays
the restoration to a normal condition
when it occurs. When the fault is
corrected, clicking the Acknowledge
button eliminates any Restoration
Reports. Conditions, which were not
rectified, remain in the window.
Not Responding Map
To assist in diagnosing problems with
the receivers and alert units
associated with a transponder, several
commands can be issued from the central
console to requesting information from
the transponder. This button requests a
map of all the devices on this
transponder (receivers or alert units)
that are not responding to the system.
The current troubles list is
automatically updated.
Jamming Map
This button requests a map of all the
receivers on this transponder that are
reporting a jamming condition to the
system. The Current Troubles list is
automatically updated.
Previous
Returns to the previous transponder.
Next
Advances to the next transponder.
Out of Service Map
This button requests a map of all
devices on this transponder (receivers
or alert units) that were manually
taken out of service to the system. The
current troubles list is automatically
updated.