Alpine IVA-D310 Manual Do Utilizador
25
-EN
01GB05IVA310.fm
ALPINE IVA-D310 68-02278Z28-A (EN)
Rear Entertainment Function
The rear entertainment function independently routes different sources
to the front and the rear inside a car. For example, while listening to the
radio or other audio source in the front, DVD can be enjoyed in the rear
with the optional rear monitor and headphones.
to the front and the rear inside a car. For example, while listening to the
radio or other audio source in the front, DVD can be enjoyed in the rear
with the optional rear monitor and headphones.
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [REAR SELECT].
Rear Select display appears.
• This function cannot be used when MONITOR OUT 1 or 2 is set
to OFF in the SYSTEM SETUP.
3
Touch the desired source such as visual (auxiliary
input, built-in DVD) to select.
input, built-in DVD) to select.
* REAR.2 is not displayed if only an external monitor is connected.
The setting screen is displayed for REAR.2 if the external monitor is
connected to the optional expansion box (VPE-S431).
connected to the optional expansion box (VPE-S431).
• Touch [OFF] to cancel the rear entertainment function.
• When the “Setting the AUX Mode” (page 34) is set to OFF, the
• When the “Setting the AUX Mode” (page 34) is set to OFF, the
auxiliary source is not displayed.
For remote control operation, the remote sensor of the external device
(monitor, etc.) can be switched, as you prefer.
(monitor, etc.) can be switched, as you prefer.
4
Touch [FRONT], [REAR 1] or [REAR 2].
The monitor which has a priority to the remote control
operation is changed.
operation is changed.
• The sensor of the touch panel rear monitor has priority over the
sensor of the remote control, if the rear monitor (connected to the
Alpine touch panel rear monitor via the Monitor control lead) is
touched, regardless of the remote control sensor switch setting. Note,
however, that the sensor of the remote control that has been set takes
priority if it has been 5 seconds since last touching the panel.
Alpine touch panel rear monitor via the Monitor control lead) is
touched, regardless of the remote control sensor switch setting. Note,
however, that the sensor of the remote control that has been set takes
priority if it has been 5 seconds since last touching the panel.
• When an optional DVD changer or DVD player is connected, and the
remote control sensor is set to REAR1 or REAR2, some touch button
operations ( [
operations ( [
] STOP, etc.) cannot be performed.
In this case, set the remote control sensor to FRONT.
Switching Display Modes
After carrying out the steps 1 to 3 of “To display the DVD mode
Screen” explained on page 27, perform the operation described below.
Screen” explained on page 27, perform the operation described below.
While your vehicle is parked, touch [WIDE] on the visual
source screen.
source screen.
Each touch changes the display modes as follows:
In Mode 1 (Wide), the monitor displays a normal picture wider to
fit in a wide-screen monitor by evenly stretching out the picture
horizontally.
fit in a wide-screen monitor by evenly stretching out the picture
horizontally.
In Mode 2 (Cinema), the monitor displays a normal picture by
stretching out the picture horizontally and vertically. This mode is
good for displaying a cinema type picture at the 16 : 9 ratio.
stretching out the picture horizontally and vertically. This mode is
good for displaying a cinema type picture at the 16 : 9 ratio.
In Mode 3 (Normal), the monitor displays a normal picture at the
center of the screen with a vertical black band at each side.
center of the screen with a vertical black band at each side.
REAR.1:
External monitor which is connected to AUX OUT of
the tuner box on this unit. (If the optional expansion
box (VPE-S431) is not connected), or an external
monitor is connected to AUX OUT1 of the optional
expansion box (VPE-S431).
the tuner box on this unit. (If the optional expansion
box (VPE-S431) is not connected), or an external
monitor is connected to AUX OUT1 of the optional
expansion box (VPE-S431).
REAR.2*: External monitor which is connected to AUX OUT 2 of
the optional expansion box (VPE-S431)
Switching the function of the remote
sensor
sensor
FRONT:
The remote sensor of this unit is effective.
REAR1:
The remote sensor of the external monitor
connected to AUX OUT of the tuner box of this
unit, or the optional expansion box (VPE-S431)
is effective, and the remote control can operate
only the source selected for the terminals.
connected to AUX OUT of the tuner box of this
unit, or the optional expansion box (VPE-S431)
is effective, and the remote control can operate
only the source selected for the terminals.
REAR2:
The remote sensor of the external monitor
connected to AUX OUT of the optional
expansion box (VPE-S431) is effective, and the
remote control can operate only the source
selected for the terminals.
connected to AUX OUT of the optional
expansion box (VPE-S431) is effective, and the
remote control can operate only the source
selected for the terminals.
MODE 1
MODE 2
MODE 3
MODE 1
(WIDE)
(CINEMA)
(NORMAL)
(WIDE)
01GB00IVAD310.book Page 25 Wednesday, December 1, 2004 4:20 AM